K-WANG
- Telephone:+86-15305925923
- contacts:Mr.Wang
- Email:wang@kongjiangauto.com
The 4-Channel Analog Current Input module for the Series 90-30 Programmable Logic Controller provides four input channels, each capable of converting an analog input signal to a digital signal for use as required by your application. This module provides two input ranges. The default range is 4 to 20 mA with user data scaled so that 4 mA corresponds to a count of 0 and 20 mA corresponds to a count of 32000 with each 1000 counts representing 0.5 mA. When a jumper is added to the I/O terminal board, the input range is changed to 0 to 20 mA with user data scaled so that 0 mA corresponds to a count of 0 and 20 mA corresponds to a count of 32000 with each 800 counts representing 0.5 mA. Two range jumpers are provided with the module; one for channels one and two, and the other for channels three and four.
GE-IC693ALG221-Analog Current Input - 4 Channel
Conversion speed for each of the four channels is one-half millisecond. This provides an update rate of two milliseconds for any channel. Resolution of the converted signal is 12 bits binary (1 part in 4096) over either range. User data in the %AI registers is in 16-bit 2’s complement format. The placement of the 12 bits from the A/D converter in the %AI data word is shown below. The relationship between the current input and the data from the A/D converter is shown in Figures 3-14 and 3-15
If the current source is reversed into the input, or is less than the low end of the current range, then the module will output a data word corresponding to the low end of the current range (0000H in %AI). If an input that is out of range is entered (that is, it is greater than 20 mA), the A/D converter will output up to full scale (corresponding to 7FF8H in %AI). Input scaling is shown in the next figure
IC693ALG221 Analog Input Module Field Wiring Information The following figure provides information for connecting field wiring to the user terminal board on the 4-Channel Analog Current Input Module. TERMINALS FIELD WIRING 1 3 5 7 9 11 13 15 17 19 4 8 10 14 16 18 20 12 2 6 a44560 * 0–20MA CH1/2 * 0–20MA CH3/4 COM GND * COM GND * COM GND * COM GND * * OPTIONAL CONNECTIONS ( + ) ( – ) ( + ) ( – ) ( + ) ( – ) ( + ) ( – ) FIELD WIRING CH1 CH2 CH3 CH4 * * * * Figure 10-8. Field Wiring for 4 Channel Analog Current Input Module Note In order to limit common-mode voltages, each current source common line may also be tied to its associated COM terminal if the source is floating. These optional connections are shown in the figure above. Please refer to Chapter 2 for wiring and shield ground connection details.
| User name | Member Level | Quantity | Specification | Purchase Date |
|---|
-
Electric tricycle truck, agricultural tricycle, elderly vehicle, warehouse truck -
GE 8042-CC-85 Carrier extension cable, 0.85m -
GE 8086-FC-20 20 + 24 pin cables for 8619 (2m) -
GE 8041-CC-35 Carrier extension cable, 0.35m -
GE 8085-FC-10 20 + 24 pin cables for 8619 (1m) -
GE 8034-CC-12 Intrinsically Safe Carrier Extension
-
GE 8082-FC-30 16-pin cable for 8618 (3m) -
GE 8030-CE-RH Intrinsically Safe Carrier extender, right hand -
GE 8080-FC-10 16-pin cable for 8618 (1m) -
GE 8021-CE-LH Carrier extender, left hand -
GE 8044-CC-20 Carrier extension cable, 2.0m -
GE 8725-CA-RB Railbus isolator carrier with PFM -
GE 8712-CA-NS Node services carrier, Profibus-DP LAN -
GE 8724-CA-PS Intrinsically Safe module power supply carrier
-
GE 8711-CA-NS Node services carrier, screw terminal LAN -
GE 8723-CA-RB Railbus isolator carrier -
GE 8606-FT-RT Field terminal, RTD -
GE 8620-FT-MT Field terminal assembly
-
GE 8604-FT-FU Field terminal, fused -
GE 8617-FT-NI Field Terminal, non-incendive, for 16 ch DI -
GE 8601-FT-NI Field terminal, non-incendive (Div 2) -
GE 8215-DO-IS 4-channel Intrinsically
-
GE 8202-HO-IS 8-channel Intrinsically Safe Analog Output, 4-20 mA with Hart -
GE 8206-TI-IS 8-channel Intrinsically Safe RTD input -
GE 8201-HI-IS 8-channel Intrinsically Safe Analog Input, 4-20mA with Hart -
GE 8117-DO-DC 8-channel DO, 2-60Vdc isolated, unpowered -
GE 8810-HI-TX 8-Channel Safety AI, 4-20mA with HART -
GE 8142-DO-DC 16-channel Digital Output
-
GE 8140-DI-AC 16-channel Digital Input, 115VAC isolated, sinking -
GE 8112-DI-AC 8-channel DI, 115Vac non-isolated, module powered -
GE 8139-SH-DC 126-channel Addressable Smoke and Heat
-
GE 8111-DI-AC 8-channel DI, 115Vac isolated, sinking -
GE 8133-HI-TX 8-Channel Supervised AI with HART -
GE 8110-DI-DC 8-channel DI, 24Vdc non-isolated, module powered
-
GE 8109-DI-DC 8-channel DI, 24Vdc isolated, sinking
-
GE 8129-IO-DC 8-channel Supervised Discrete I/O -
GE 8106-TI-RT 4-channel RTD input
-
GE 8127-DI-SE 32-channel SOE module -
GE 8105-TI-TC 4-channel THC/mV input -
GE 8125-DI-DC 32-channel DI, non-isolated, module-powered -
GE 8104-AO-IP 8-channel AO, 4-20mA -
GE 8122-DI-DC 16-channel DI, 24Vdc isolated, sinking
-
GE 8103-AI-TX 8-channel AI, 4-20mA -
GE 8121-DI-DC 16-channel DI, 24Vdc non-isolated
-
GE 8102-HO-IP 8-channel AO, with HART for 4-20mA
-
GE 8119-VI-05 8-channel Voltage Input, 1-5Vdc -
GE 8101-HI-TX 8-channel AI, 4-20mA with HART -
GE 8755-CA-NS EBIM carrier -
GE 8522-EB-MT Ethernet Bus Interface -
GE 8752-CA-NS Universal Node Services Carrier -
GE 8515-BI-PN PROFINET Scanner Module -
GE IC754VBI12CTD Touch Screen -
GE IC754VGI10MTD Touch Screen -
GE IC754VBI1OMTD Touch Screen -
GE IC754VSL12CTD QuickPanel -
GE IC754VBL12CTD QuickPanel -
GE IC754CGL12CTD QuickPanel
-
GE IC754CBL12CTD QuickPanel -
ABB TZIDC Digital Positioner -
ABB NextMove ESB-2 motion controller -
ABB Advant Controller 70 -
ABB Advant Controller 250 -
ABB ACS850-04 drive modules -
ABB IRB 4600 Industrial Robot -
ABB IRB 910SC SCARA -
ABB Product specification IRB1200 -
ABB DCV 700 thyristor panels -
ABB Advant Controller 160 -
ABB Serial Communications Module RS232 -
ABB PP886 Compact Product Suite hardware selector -
ABB Panel 800 version 6 -
ABB Uvisor™ FAU810 – Flame Analysis Unit -
ABB Switches Automatic Transfer Switches -
ABB Dynamic braking / DC drive -
ABB Automatic Transfer Switch OTM_C_21D -
ABB Switches Change-over and transfer switches -
ABB PGC2000 Series Process Gas Chromatograph -
ABB PGC5000 Series gas chromatographs -
ABB DBDID Process gas chromatographs -
ABB Vapor Pressure (RVP) analyzers -
ABB Distributed busbar protection REB500 -
ABB SYNCHROTACT® upgrade Keep your assets synchronized, safe and productive -
ABB SYNCHROTACT® Datasheet Synchronizing devices and systems
-
ABB C310 Wall- / Pipe-mount universal process controller -
ABB AP100 pH/Redox (ORP) cartridge sensors with water-wash option -
ABB Title this is title and subtitle this is subtitle Power Factor Controller RVC Accurate control and monitoring of capacitor banks -
ABB FOUNDATION Fieldbus Linking Device LD800HSE EX -
ABB Remote Terminal Unit RTU560 -
ABB MEASUREMENT & ANALYTICS TEIP11 -
ABB MEASUREMENT & ANALYTICS Navigator 540 -
ABB For electromagnetic flowmeters FXE4000-DE43F -
ABB COM610 Communication Gateway -
ABB Symphony Plus S+ Control BRC410 -
ABB Symphony Plus SD Series PROFIBUS Interface: PDP800 -
ABB Symphony Plus SD Series HART I/O: HAI805 and HAO805 -
ABB Symphony Plus S+ Turbine: Auto Synchronizer Module AS800
-
ABB S900 I/O Application-Guide CI920S/CI920B replaced by CI920AS/CI920AB
-
ABB S800 I/O Communication interfaces Compact Product Suite -
ABB S800 I/O Communication interfaces Compact Product Suite -
ABB IndustrialIT System 800xA S800 I/O System
-
ABB Advant® Master S100 I/O system -
ABB Ability™ Symphony® Plus MR Series (Melody Rack) -
ABB Data Sheet ControlIT Harmony Analog I/O
-
ABB Bailey* network90 Loop Interface/Bus Interface(LIM/BIM) -
ABB Bridge Controller and Process Bus Adapter BRC-300 and PBA-200 -
ABB Kent Morrisey, Business Development Manager – Harmony Evolution NA Harmony Evolution Options For Process Industries Users -
ABB Industrial'T System 800xA Harmony/INFI90 System
-
ABB Ability™ Symphony® Plus HR Series Control and I/O -
ABB AC700F controller with direct S700 I/O
-
ABB ContransIthe family with Instruction Manual for Freelance 2000 -
ABB AC servo motors BSM Series -
ABB BSD Series
-
ABB ControlMaster CM10 Universal process controller, 1/8 DIN -
ABB PGC2000 Advance Training Course Synopsis
-
ABB PGC5000 Series gas chromatographs -
ABB EasyLine EL3000 Series Continuous gas analyzers -
ABB AO2000 Advance Optima Continuous gas analyzers -
ABB Advant® Controller 450
-
ABB Advant® Controllers -
ABB Ability™ System 800xA -
ABB Advant® Master S100 I/O system -
ABB SYNCHROTACT®5 Operating Instructions -
ABB Web Tension Systems with Tension Electronics PFEA111 -
ABB Pressductor Pillowblock Load Cells Vertical Measuring PFCL201 -
ABB Force Measurement Products Cold rolling and processing of steel -
ABB DCS800 Drives
-
ABB MNS iS motor control center -
ABB Condition MonitoringMService
