AB 1794-IE8H FLEX I/O 8 Input HART Analog Module

AB 1794-IE8H FLEX I/O 8 Input HART Analog Module

IMPORTANT USER INFORMATION: Emphasises the differences between solid-state equipment and electromechanical equipment, use of this module is to ensure that the application complies with the requirements, Rockwell Automation is not responsible for consequential damages arising from the use of the equipment, and the manual examples are for reference only and may not be reproduced without permission. Also includes a variety of safety tips, such as operating in hazardous environments and protection against static electricity.

Installation requirements: For use in pollution class 2, overvoltage category II, industrial environments up to 2000 metres above sea level, Group 1, Class A industrial equipment. Installation in a flame-retardant, tool-accessible enclosure to fulfil EMC and safety requirements. Use zinc-plated yellow chrome steel DIN rails for grounding and avoid using other rail materials that may cause poor grounding.

Approved for use in hazardous areas

North America: This module is approved for use in hazardous areas in North America. The product is labelled with a temperature code and the overall temperature code and local regulatory review should be noted when combining devices. When operating in a hazardous area, electrical disconnections or connections are not permitted, and operations such as battery replacement must be performed in a non-hazardous area.

Europe: European Zone 2 approved for use in potentially explosive atmospheres. The device must be used in an enclosure of at least IP54 protection, protected from direct sunlight, protected from voltage overruns, and must have an ATEX approved backplate.

Module Installation

Preparation for Installation: The module must be used with either the 1794-TB3G or 1794-TB3GS terminal block. Ensure that no debris has fallen into the module prior to installation, and disable the keying function in the configuration file when replacing a Series A module with a Series B module.

Installation Procedure: Rotate the key switch to position 3, ensure the Flexbus connector is fully extended, insert the module and align it with the notch for a secure installation. Once installed, remove the end cap plug and connect additional terminal blocks if required.

Wiring and Grounding

Wiring: When connecting a two-wire transmitter device, the input, power, and common wires need to be connected according to specific rules, power supplies can be daisy-chained, and analogue and digital modules should be powered separately to minimise noise interference.

Grounding: All I/O wiring must be shielded and the shield must be externally grounded to the module, e.g. to a busbar or shielded ground feedthrough.

Module Configuration: Set module parameters such as byte order, data format, digital filters, alarm limits, etc. through the configuration mapping table. The data format is various and can be selected according to requirements. Different settings correspond to different functions and value ranges. The configuration in Series A mode is different from that in Series B mode, so it is necessary to pay attention to the applicable scenarios.

HART input data: HART input data contains the main variables of the device and other information, if the HART communication of the channel is disabled, the input data of the channel may be zero, HART input data word contains the communication status, device status, variable acquisition and other information, and each status bit has a clear meaning.

Status Indicators: The module is equipped with 8 red fault indicators, 8 yellow channel indicators and 1 green power indicator. Different indicator statuses reflect different working statuses of the module, such as blinking red indicates channel fault, green light indicates normal power supply, blinking green indicates no Flexbus communication, and yellow light indicates normal HART communication.

Basic Parameters

Number and type of inputs: 8 single-ended, non-isolated analogue input channels, suitable for analogue signal acquisition in various industrial scenarios.

Recommended Terminal Block: Adapted to 1794-TB3G and 1794-TB3GS terminal blocks, ensuring stable connection between the module and external devices.

Key switch position: fixed to 3, used to set the module's working mode.

Enclosure type rating: None (open), to be installed in an additional protective enclosure to meet the protection requirements of the specific application environment.

Electrical parameters

Resolution and data format: resolution up to 16 bits, data format can be configured to support a variety of data representation to meet different measurement and control needs.

Conversion correlation: using the successive approximation method for conversion, can accurately convert analogue signals to digital signals.

Accuracy and anti-interference: Absolute accuracy of 0.1% full scale at 20°C (68°F), 0 - 55°C (32 - 131°F) accuracy drift of 0.05% full scale, with good stability. It has a certain ability to suppress interference signals of different frequencies, which can ensure the accuracy of the signal to a certain extent.

Input Characteristics: Input terminals are specifically numbered for connection to external signals. When the 24V DC power supply is removed, the input resistance becomes 10 kΩ.

Isolation and power supply: Isolation voltage is 50V (continuous), basic insulation type, tested at 850V DC for 1s to ensure electrical safety Flexbus current is 80 mA at 5V DC and 190 mA at 24V DC; power supply requirements are 24V DC (voltage range 19.2-31.2V DC with 5% AC ripple), powered by a 1794-PS13 power supply at 31.5V DC. The PS13 power supply has a maximum power consumption of 3.9W at 31.2V DC and a maximum thermal dissipation of 13.5BTU/hr.

Physical Parameters

Dimensions and Weight: Measures approximately 46.0 x 94.0 x 75.0mm (1.8 x 3.7 x 2.95in.) when mounted and weighs approximately 200g (7.05oz) for ease of installation in equipment layouts.

Indicator Lights: Equipped with 8 red fault indicator lights, 8 yellow channel indicator lights and 1 green power indicator light, which indicates the working condition of the module through different colours and statuses for easy monitoring.

Wire-related: Wire size is determined by the installed terminal block, shielded wires are used for signal ports, and the wiring category is Class 2 for both signal and power ports, which can be used for planning wire routing.

Environmental parameters

Temperature range: Operating temperature - 20 - 55°C (-4 - 131°F), storage temperature - 40 - 85°C (-40 - 185°F), can be adapted to a certain range of temperature changes .

Humidity and others: Relative humidity requirements of 5 - 95% non-condensing; able to withstand a certain degree of vibration and shock, vibration conditions for the 2g @ 10 - 500Hz, operating shock and non-operating shock of 15g; in terms of electromagnetic compatibility, in line with the relevant standards, such as CISPR 11 in the Group 1, Class A standards (with a suitable enclosure), the Electrostatic Discharge (ESD), radiation radio frequency (RF), electrical rapidity of （It is immune to electrostatic discharge (ESD), radiated radio frequency (RF), electrical fast transient pulse bursts (EFT/B), surge transients and conducted RF.