ADLINK AmITX-AL-I ultra-thin Mini ITX industrial motherboard

ADLINK AmITX-AL-I ultra-thin Mini ITX industrial motherboard

Product Overview

1.1 Product positioning

Ultra thin 170 × 170mm Thin Mini ITX low-power industrial motherboard, designed for digital signage, automotive industrial control, medical equipment, self-service terminals, and IoT edge devices; Equipped with Intel Apollo Lake Atom/Pentium/Celeron single-chip SoC, it has a long lifecycle, low power consumption, multi screen display, built-in SEMA machine management BMC, and supports customized models with wide temperature range.

1.2 Full range SoC models and power consumption

Model Core/Frequency TDP/SDP

Atom x7-E3950 4-core 1.6/2.0GHz 12W

Atom x5-E3940 4-core 1.6/1.8GHz 9.5W

Atom x5-E3930 2-core 1.3/1.8GHz 6.5W

Pentium N4200 4-core 1.1/2.5GHz 6W (SDP4W)

Celeron N3350 2-core 1.1/2.4GHz 6W (SDP4W)

All CPUs are equipped with 2MB cache and support VT-x and VT-d virtualization technologies.

1.3 Overview of Core Hardware

Memory: Double layer stacked SODIMM dual channel DDR3L 1600/1866MHz, maximum 16GB, non ECC

BIOS: 16MB SPI AMI EFI UEFI firmware, supports dual BIOS fault recovery, serial console, secure boot

Graphics: Gen9 low-power core display, hard decoding H.265/H.264/VP9, supports independent output of 3 screens

Network: Dual Intel I211AT Gigabit RJ45; Switch to I210 PHY for wide temperature version

Storage: 2-channel SATA 6Gbps, mSATA slot multiplexed with SATA1

Expansion: PCIe x1 full height slot, full height Mini PCIe (with USB), SIM/microSD as onboard customization options

Serial port: 6-way COM, COM1/2 supports RS232/422/485, COM3-6 only supports RS232

Power supply: Single 12V DC input, supports AT/ATX two power on modes

Management: Built in SEMA BMC substrate management controller, integrated watchdog, voltage, current, and temperature monitoring

1.4 Display output specifications (three screen combination)

Rear: 1-channel HDMI 1.4b (up to 3840 x) 2160@30Hz ）1 way DP1.2 (highest) 4K@24Hz Can be customized with dual DP instead of HDMI)

Onboard optional: Single/dual channel 18/24bit LVDS or 4-lane eDP, up to 1920 × 1200@60Hz

Combination: DP+HDMI+LVDS/eDP three screens working independently at the same time

1.5 IO complete list

Rear exposed IO

12V DC lock type power port DP、HDMI、 Dual gigabit network, 4xUSB3.0, audio output/microphone

Onboard pins

6-way COM, 2-channel USB2.0, front USB/audio, 2xSATA, SATA power supply, PS/2 keyboard and mouse, LVDS/eDP backlight, GPIO/I2C/SMBus, CPU/system fan, 20 pin front panel (power on/off/reset/indicator light), 40 pin DB40 debugging interface (BIOS burning, POST debugging)

1.6 Environment and Power Consumption

Temperature: Standard 0~60 ℃; Atom customized wide temperature version -40~85 ℃; Humidity 10%~90%, no condensation

Vibration impact: Complies with MIL-STD-202G industrial standard, passed HALT accelerated aging test

Tested power consumption (with 4GB memory and SSD)

Saiyang N3350: standby 33.99W, full load 50.60W

Pentium N4200: standby 35.58W, full load 54.75W

Atom E3930: standby 39.84W, full load 53.25W

Atom E3940: standby 45.26W, full load 63.59W

Atom E3950: standby 46.32W, full load 75.70W

Sleep S3 only 0.84W, shutdown S5 energy-saving mode as low as 0.12W

1.7 Operating System Support

Windows10 64bit、Fedora、RHEL Linux； VxWorks BSP TBD

Mechanical Layout and Dimensions

Size standard Thin Mini ITX: 170mm × 170mm, board thickness<18.3mm (excluding battery)

Mechanical dimension diagram of motherboard

Component layout: Annotate CPU, dual SODIMM, PCIe x1, Mini PCIe/mSATA, LVDS, COM pins, fans, various jumpers

Bottom of solder pad: microSD, SIM card slot, DB40 debugging 40pin cable socket

Rear interface of motherboard

Complete Definition of Connectors and Jumpers

Rear External Interface

12V DC lock type power supply: It is prohibited to connect the built-in 4pin ATX power supply at the same time, and it cannot be hot swappable

DP/HDMI complete differential, DDC, HPD pin definitions

Dual Gigabit RJ45: 8-wire Gigabit differential, dual color link/rate indicator light

USB 3.0 standard 9-pin high-speed differential interface

3.5mm audio output/microphone jack, shared with onboard audio pin signal

Key points of internal onboard connectors

SATA1/mSATA reuse: JP11 jumper switching, selecting mSATA will render SATA1 invalid

LVDS backlight: JP2 backlight 5V/12V switching; JP4 backlight high and low level enable; JP3/JP5 LCD screen power supply 3.3V/5V/12V three levels optional

COM1/2 serial port: SWS1M/SWS2M dial-up switch RS232/422/485; JP7~JP10 select serial port power supply 0/5/12V

AT/ATX mode jumper JP1:1-2 AT constant power supply, 2-3 standard ATX

Clear CMOS jumper JP6: Power off, short circuit 2-3, clear BIOS and system time

Front panel 20 pin: power button, reset, hard drive LED, system sleep indicator, front USB/audio

Feature 28 pin expansion pins: 10 GPIO, I2C/SMBus, chassis lid opening detection, temperature analog input

Dual fan socket: CPU fan, system fan, SEMA can read speed, PWM speed regulation

DB40 debugging cable: used for BIOS burning, POST fault codes, BMC debugging, power testing points

Key Jumper Table

General diagram of jumper positions

Table

Jumper/switch function

JP1 AT/ATX power supply mode

JP6 Clear CMOS clears BIOS

JP11 SATA1/mSATA switching

JP2 LV backlight 5V/12V

JP3/JP5 LVDS screen power supply voltage

JP4 backlight enable level

SWS1M/SWS2M COM1/2 serial protocol switching

JP7~JP10 COM serial port power supply selection

SEMA Intelligent Embedded Management System (Core Industrial Features)

SEMA is an onboard independent BMC microcontroller that does not rely on CPU/system. It can monitor the basic status even when the whole machine is powered off, and its functions fully cover industrial remote operation and maintenance needs

Hardware monitoring and collection items

Voltage acquisition: CPU core display, memory, 12V input, 5V, 3.3V, standby 3.3V, RTC battery

Current monitoring: Real time input of total current, sampling and saving 4 sets of historical values every 250ms

Temperature: CPU, motherboard startup/minimum/maximum temperature, over limit alarm

Fan speed reading, supporting intelligent temperature control curve

Logging and Counting Function

Total running time of the whole machine, single boot time, total power on times, BIOS boot count

System restart traceability record: power failure, watchdog, external reset, BIOS fault classification tag

1KB customer customized Flash storage area, 128 byte encrypted protected partition (serial number/key storage)

Watchdog WDT

The power on automatic watchdog can be BIOS turned on/off; Timeout automatic hard reset, software configurable timing duration, restart can read whether WDT triggers downtime

Dual BIOS Fault Redundancy

BMC automatically switches to backup BIOS firmware when BIOS startup exception occurs to prevent firmware damage and inability to boot up

Alarm mechanism

Hardware abnormalities (overheating, undervoltage, power loss) are encoded through the blue status light, and the BMC register synchronously stores the abnormal code, which can be read and troubleshoot by software

Supporting Tools

SEMA Windows/Linux software, underlying API library, supports reading all monitoring data, controlling backlight, turning on/off watchdog, and reading boot logs

System Bottom Level Resource Mapping

Provide a complete address table for the bottom layer of industrial control secondary development:

System memory address range (4GB high-order BIOS, APIC, ISA reserved holes)

Hexadecimal allocation of IO ports (serial port, SuperIO, SATA, PCI controller)

PIC/APIC two modes IRQ interrupt allocation table

PCI/PCIe device bus, device, function number topology

PCI interrupt routing mapping, SMBus slave device address (memory, BMC, GPIO extension)

AMI EFI BIOS Complete Menu Description

Press Del to enter UEFI settings during startup, which is divided into 7 main menus and supports serial remote console (COM1-6 optional)

Main Page

Read only motherboard serial number, manufacturing date, CPU/memory information; System date and time can be modified

Advanced Menu (Industrial Control Core Configuration)

CPU settings: VT-x/VT-d virtualization, turbo frequency, C-State energy-saving, temperature protection

Graphics card configuration: LVDS/eDP resolution, backlight brightness, priority for multi screen output

Power management: ACPI sleep mode, RTC timed power on, power-off restoration to power on state, ECO ultra-low shutdown power consumption

System management: SEMA firmware version, boot counter, watchdog switch, fan intelligent speed control gear

Thermal management: CPU/motherboard temperature threshold, mute/balance/performance fan strategy

Super IO: 6-way serial port address IRQ allocation, RS485 direction control

Serial port redirection: supports remote debugging BIOS POST without display

USB、 Network, SDIO, TPM trusted computing, chassis intrusion detection switch

Chipset Chipset Menu

North Bridge: Memory frequency, memory remapping above 4G, DVMT allocation for core graphics and video memory

South Bridge: SATA AHCI/RAID switching, PCIe speed, HD audio, USB controller switch

Security Menu

Administrator/user two-level boot password, Secure boot configuration

Boot startup menu

Startup sequence, fast self-test, UEFI/Legacy compatible CSM switch, PXE network boot

Save & Exit

Save/abandon restart, load optimal/fail safe default BIOS parameters, single temporary boot device

Safety operation standards

Disassembly and assembly must be done with anti-static wristbands and workbenches. Damage caused by static electricity is not covered by warranty

The 12V power supply is not hot swappable, and it is prohibited to connect both the rear DC and the built-in ATX power supply simultaneously

The replacement model of the CR2032 lithium battery on the motherboard is incorrect and there is a risk of explosion. The waste battery is being recycled in compliance with regulations

4. The working environment should not block the air ducts, and wide temperature models still need to be matched with heat dissipation solutions

Private disassembly, water ingress, mismatched voltage, and physical impact are not covered by the warranty