ADLINK NuPRO-595 series half length Socket 7 industrial motherboard



ADLINK NuPRO-595 series half length Socket 7 industrial motherboard

Comparison of core differences between NuPRO-595/596 products

Both are 185 × 122mm half length ISA industrial boards, with Socket7 architecture and Intel 430TX chipset. The core difference is only the network port:

|Parameters | NuPRO-595 | NuPRO-596|

|Processor | Pentium MMX, low-power Pentium, AMD K6-2/K6-3, Cyrix MII | Same as 595|

|Chipset | Intel 82430TX Northbridge+82371EB Southbridge | Completely Consistent|

|Cache | Onboard 512KB L2 Cache | Completely Consistent|

|Memory | Single 168 pin SDRAM DIMM, maximum 128MB | Completely Consistent|

|Display | C&T 69000, supports CRT+LCD dual display | completely consistent|

|Serial port | COM1 RS232, COM2 switchable RS232/422/485 | Completely consistent|

|Watchdog | 0~255 seconds/minute programmable | completely consistent|

|Hardware Monitoring | Winbond W83781D (Voltage/Fan/Temperature/Chassis Open Cover Detection) | Completely Consistent|

|Storage | Ultra DMA33 IDE, floppy drive, DOC solid-state drive slots | Completely consistent|

|Network card | Onboard Intel 82559 10/100M, supports WOL remote wake-up | No onboard network port|

|I/O | 2 serial ports+1 parallel port+USB 1.0 | Completely consistent|

|Size/Power Supply | Half length ISA board, supports AT/ATX power supply | Completely consistent|

Hardware installation (CPU/memory/jumper/interface definition)

CPU and memory installation steps

1. CPU: Lift the Socke7 lever and align it with the notch to install it. After locking, it must be matched with JP7 multiplier and JP9 core voltage jumper wires, and equipped with a heat sink to avoid overheating and crashing;

2. Memory: Single 168 pin DIMM slot, supporting 16/32/64/128MB SDRAM, fixed with a snap fastener.

All jumper functions (core configuration switch)

1. JP7: CPU multiplier jumper, matched with different clock speeds of Pentium/AMD/Cyrix;

2. JP9: CPU core voltage (multiple levels of 1.9V~2.8V);

3. JP4/JP5: CPU IO voltage switching between 2.5V/3.3V;

4. JP1: LCD screen power supply 3.3V/5V selection;

5. JP2: Clear CMOS (short circuit 1-2 to clear BIOS settings, 2-3 runs normally);

6. JP11/JP12/JP13: COM2 serial port protocol switching (232/422/485);

7. JP6: External system temperature sensor;

8. JP8: Chassis cover opening detection sensor pin.

Complete pin definitions for all onboard connectors

Including motherboard layout drawings and all pin signals:

-CN4 multifunctional pins: power switch, reset, power LED, hard disk LED, chassis speaker, keyboard lock;

-CN5 50pin LVDS LCD screen interface: compatible with various TFT/DSTN screens;

- IDE、 Soft drive, VGA, RJ45 Ethernet port, dual serial port, parallel port, PS2 keyboard and mouse, USB, CPU fan, ATX power plug;

Supporting LED status description: Green light link and yellow light data flashing distinguish 10/100M network speed.

Award BIOS Complete Setup Manual

Press Del to enter the BIOS main menu. Detailed explanation of all industrial control specific parameters:

1. Standard CMOS settings

System time, IDE hard disk automatic recognition, floppy drive type, display output (CRT only/LCD only/dual display), startup error shutdown strategy.

2. BIOS Function Settings

Virus protection, CPU internal and external cache switch, power on self-test speed, boot sequence (floppy disk/hard disk/network/SCSI), digital lock, A20 address line, boot password, PXE network boot switch.

3. Chipset settings

SDRAM timing, memory holes, Spread spectrum (EMI testing), CPU overheating warning, chassis cover opening buzzer alarm, real-time read-only monitoring of various voltages.

4. Power Management PM

APM energy-saving, video shutdown strategy, multi-level sleep timing, CPU sleep speed reduction, WOL/modem remote boot, fan sleep stop, hardware wake-up interrupt configuration, supports 16 types of industrial LCD screen selection.

5. PNP/PCI configuration

Plug and play switch, IRQ/DMA resource manual allocation, compatible with old ISA industrial control cards without conflicts.

6. Integrated peripherals

IDE PIO/UDMA mode, serial parallel mode, USB keyboard, onboard VGA/network card enable switch.

7. Auxiliary functions: administrator/user dual password, loading factory/optimal defaults, automatic hard disk detection, saving/discarding, exiting BIOS.

Driver Installation Intel PIIX Bus Master IDE driver (Win95 only)

Installation prerequisites and step-by-step process, deleting real mode IDE drivers, installing file paths, troubleshooting, and improving hard disk DMA transfer speed.

C&T 69000 graphics card driver (Win95/98/NT4.0)

The installation steps for each system control panel require NT to pre install SP5 patch to adapt to LCD industrial display output.

Intel 82559 100Mbps Network Card Driver (NuPRO-595 only)

1. Support systems: Win95/98/NT, NetWare, SCO Unix, Linux, DOS group drivers;

2. Supporting diagnostic tools: automatic detection of network cards, viewing MAC/speed, loop testing, batch installation of drivers;

3. Hardware features: Bus master control, full duplex, Magic Packet remote wake-up.

Hardware Doctor Hardware Monitoring Tool

Windows platform monitoring software, paired with W83781D chip:

1. Monitoring items: Vcore, 3.3V/5V/± 12V voltage, three-way fan speed, CPU/system temperature, chassis cover opening;

2. Function: Custom upper and lower threshold values, over limit pop-up window+buzzer alarm, fault counting filtering, parameter saving/restoring to default;

3. Operating mechanism: The backend resides in the tray program, and only the 3-pin speed measuring fan supports speed reading. When the temperature exceeds the threshold, an active warning is issued to protect the CPU.