ADLINK NuPRO-840 DV/LV Full Length PICMG Industrial Single Board Computer

ADLINK NuPRO-840 DV/LV Full Length PICMG Industrial Single Board Computer

Core Differences of NuPRO-840 DV/LV Models

The two PCBs are completely identical, with only the network port configuration distinguishing them, and all other hardware, interfaces, and performance are the same:

|Hardware Item | NuPRO-840DV | NuPRO-840LV|

|Ethernet 1 | Intel 82562EM 10/100M (WFM2.0 management) | Intel 82562EM 10/100M|

|Ethernet 2 | Intel 82540EM Gigabit 10/100/1000M | No second Gigabit Ethernet port|

|Other CPU/memory/graphics card/I/O/watchdog/monitoring | completely consistent | completely consistent|

Core hardware architecture and overall specifications

1. Processor and chipset platform

-CPU: MPGA478 slot Intel Pentium 4 FC-PGA2, FSB 400MHz, main frequency 1.3~2GHz, CPU built-in 256KB L2 cache; Supporting version 9.0 VRM power supply module.

-North Bridge Intel 82845 MCH (Brookdale), supports DDR memory AGP 2X； Nanqiao ICH2 82801BA, integrated with USB, IDE, LPC bus RTC、 Interrupt/DMA controller.

-PCI to ITE8888 ISA bridge, ISA bus drive current 64mA, compatible with old ISA acquisition cards.

- Super I/O：Winbond W83627HF， Manage serial ports, parallel ports, floppy drives, hardware monitoring, and chassis cover opening detection.

2. Memory system

-Dual 184 pin DDR DIMM slots, supporting 200MHz buffered DDR;

-Maximum capacity 2GB, single line 256/512/1024MB, 2.5V voltage;

-BIOS automatically recognizes the model and frequency of SPD by reading the memory through SMBus, and comes with a complete 4GB system memory address mapping table.

3. Graphics subsystem

SiS305 independent display chip, onboard 8/16MB video memory, AGP2X interface, up to 1600 x 1200@85Hz CRT output; BIOS can turn off the onboard graphics card, free up memory for PCI dedicated display, and only support single display output.

4. Dual Ethernet (DV exclusive)

1. LAN1: Intel 82562EM 100Mbps, compatible with WFM2.0 remote device management;

2. LAN2: Intel 82540EM Gigabit, supports 802.3x traffic control and automatic negotiation;

Each RJ45 cable comes with a dual color link/speed indicator light, and the document clearly defines the light status.

5. Storage Controller (ICH2 Integrated)

Dual channel Ultra DMA 100 IDE (main CN1, secondary CN3), with a maximum of 2 hard drives/optical drives/ZIP/LS120 mounted on a single channel, supporting PIO3/4, UDMA33/66/100; IDE pin reserved for DOM solid-state drive power supply; Equipped with a 34 pin standard floppy drive interface, compatible with all specifications of floppy disks.

6. Complete list of I/O interfaces

-Serial port: COM1/COM2 dual channel 16550 UART, standard RS232, up to 115200 baud;

-Parallel port: IEEE1284 standard, supports SPP/ECP/EPP, 4KV electrostatic protection;

-USB1.1: Dual pin, independent overcurrent protection;

-PS/2 keyboard and mouse composite interface, matched with Y-shaped splitter, with an additional 5-pin external keyboard pin built-in;

-IrDA infrared transmission pin;

-AC'97 audio expansion pin (optional sub card for input and output);

-Three way CPU/chassis fan speed measurement socket;

-External temperature sensor, chassis cover opening detection pin;

-20 pin front panel pins (power light, hard disk light, reset, chassis speaker, ATX power on/off).

7. Core functions dedicated to industrial control

(1) Two level programmable watchdog WDT

-Timing gear: selectable between 1-255 seconds or 1-255 minutes;

-Two level protection logic: timeout triggers NMI unshielded interrupt first, and if there is no dog feeding, the entire machine hardware is reset; The register can read the reset source and distinguish between watchdog restart and normal power on;

-Provide 8086 assembly low-level configuration example code, paired with DOS/Windows testing tools.

(2) SMBus system hardware monitoring

Based on the I2C bus, real-time monitoring of various power supply voltages, CPU/chassis temperatures, three-way fan speeds, and chassis lid opening events; The power failure of the lid opening signal can be locked, and the alarm needs to be cleared by software.

(3) Reset dual mechanism

-Hard reset: Cut off all peripheral clocks and restart the entire machine completely;

-Soft reset: Only reset the CPU core, keep external devices such as hard drives/network cards running;

Reset source: panel reset button CTRL+ALT+DEL、 Watchdog, ICH2 register instruction.

8. Electrical, environmental, and mechanical parameters

1. Power consumption: P4 2.4GHz+1GB full load machine approximately 85.72W (excluding peripherals);

2. Environment: Working at 0-60 ℃, storage at -40-85 ℃; Humidity of 5%~95% without condensation;

Vibration/shock: working at 0.5Grms, 3G peak; Transport 6Grms, 30G peak;

3. Size: Full length PICMG standard 338mm × 122mm;

4. Power supply: Compatible with AT/ATX power supply, supports network wake-up WOL and modem ringing for startup.

Jumper and hardware configuration

The whole machine only has one set of core jumper JP1: clear CMOS (2-3 short circuited for 2 seconds to clear BIOS settings, 1-2 is in normal mode);

All other functions (serial port mode, video memory size, boot options, interrupt allocation) are configured in the Award Phoenix BIOS software;

The document comes with a full motherboard connector point map, indicating the physical positions of all pins from CN1 to CN33.

BIOS Settings Overview

Phoenix Award PnP Flash BIOS (512KB firmware hub), press Del to enter the settings menu when booting up, core functions:

1. Standard CMOS: system time, hard disk automatic recognition, boot sequence;

2. Chipset settings: DDR timing, AGP memory allocation, hardware monitoring threshold;

3. Integrated peripherals: IDE/serial/parallel/USB/Ethernet switch;

4. Power management: multi-level sleep mode, WOL remote power on, fan temperature control;

5. PnP resources: IRQ/DMA manual allocation to resolve ISA card conflicts;

6. Startup function: PCIe network diskless boot, boot password, virus protection;

The complete I/O address mapping table is attached to the manual, listing all standard ports of onboard peripherals.

Complete driver step-by-step installation

The supporting driver CD supports Windows 95/98/ME/NT4.0/2000/XP, and is divided into three categories of drivers for complete installation process:

Intel 845 chipset INF driver: To repair PCI/AGP resources, it must be installed first and provide a one click setup program;

2. SiS305 graphics card driver: divided into 9X/NT/2000/XP independent installation packages, NT4 needs to be pre patched with SP4 patch; Reminder: Coexistence of multiple PCI graphics cards may result in blue screens. It is recommended to disable the onboard graphics card;

3. Dual network card driver (82562/82540): Manual update steps for Win versions, NT requires creating a driver floppy disk, supporting network card diagnostic tools, and supporting loop testing and speed detection.

Watchdog Development Guide

1. Hardware architecture register description and two-level timeout logic;

2. Example of low-level assembly configuration source code, showing the complete process of 15 second timeout reset;

3. Equipped with cross platform testing programs, it can be directly embedded into industrial control monitoring software to achieve automatic restart in case of system failure.

Definition of all connector pins

Complete list of all pins and signals on the motherboard, including VGA, RJ45 Gigabit/100Mbps Ethernet ports, PS/2 keyboard and mouse, dual serial ports, parallel ports, etc IDE、 Soft drive USB、AC97、SMBus、 Electrical definitions for all interfaces such as infrared, fan, temperature sensor, front panel 20 pin, and chassis cover opening pin, along with accompanying LED indicator status instructions.