K-WANG



Core features and advantages of the product
PCI bus standard: compatible with PCI r3.0 64 bit, 66MHz; Backward compatible with PCI r2.2, with 5V fault-tolerant I/O.
Port architecture: The primary and secondary ports adopt asynchronous design; Supports 33/66MHz bus operating frequency; Comes with main port PCI frequency detection.
Scalability: Two PMC card slots are provided on the board, which can accommodate two standard PMC daughter cards.
Cooling version: Provides two hardware versions: Air cooled and conduction cooled, suitable for commercial or reinforced harsh working conditions.
Typical applications
data acquisition system
Automatic testing equipment
Detection and verification system
Product Overview
DP-VME-5114 is a 6U VME specification PMC carrier board that accommodates 2 PMC (PCI mezzanine daughter cards) in a single standard VME slot.
PMC sub cards can provide modular and cost-effective hardware solutions for process control, medical electronics, aerospace, defense, and telecommunications industries.
Working principle (PCI-PCI bridge)
On board PCI-PCI bridge chip (PCI6466): obtains the main PCI bus signal from the VME backplane P0 connector, bridges and generates the secondary PCI bus on the board; Two PMC slots are mounted on the secondary PCI bus.
Backplane P0 provides IDSEL, clock, PCI request/authorization signals; The backplane handles the rotation of interrupt lines, and the interrupt signal is transmitted back to the main PCI bus (P0) through the bridge chip.
I/O dual output:
Rear I/O: relying on VME64 high-density P2 connector to achieve high-density rear signal output;
Front I/O: The 25 pin D-Sub connector leads out 18 front I/O signals.
Detailed characteristics of PCI-PCI bridge (PCI6466)
Supports up to 33MHz/66MHz PCI bus, with internal arbitration, and supports up to 4 PCI devices on the secondary side.
Support burst transmission mode to improve throughput; The main and secondary bus traffic paths are independent of each other; Working in transparent mode.
The PMC module clock is provided by an external 33/66MHz crystal oscillator as a secondary PCI clock source.
The board generates 4 secondary interrupt requests, which are routed and forwarded to the main PCI bus.

Software Description
The PCI-PCI bridge on the board is automatically identified and enumerated by the operating system; The carrier board itself does not provide independent drivers.
The actual inserted PMC daughter card requires the corresponding operating system driver provided by the PMC daughter card itself to achieve full functionality.
Technical specifications
PMC compliance: Complies with IEEE P1386.1/Draft2.3 PMC specifications.
Electrical and mechanical interface: supports 2 standard single size PMC modules; Supports 64 bit, 66MHz PCI bus.
PCI standard: Following PICMG 2.0 R3.0 specification.
Connector List
Connector Function Description
P1 (VME J1) 160 pin right angle female socket, VME backplane power supply interface
P2 160 pin right angle female socket, PMC rear I/O signal
P0 (VME J0) 95 pin connector, transmitting PCI bus signals
PMC 64 pin socket PMC daughter card standard interface
25 pin D-Sub leads out 18 front-end I/O signals
Power requirements (maximum single slot limit for each PMC slot)
+5V: Single PMC slot maximum 2A, total current=slot 1+slot 2
+3.3V: Single PMC slot maximum 3A, total current=150mA+slot 1+slot 2
+12V: Single PMC slot maximum 200mA, total current=slot 1+slot 2
-12V: Single PMC slot maximum 200mA, total current=slot 1+slot 2
Mechanical Specifications
Following the VME64x ANSI/VITA 1.1-1997 standard, the 6U dual European card size is 233.3mm × 160mm, occupying a single VME slot.
Environmental Grade
Two environments: Commercial and Rugged.
Order code DP-VME-5114-X-0-0
Number 1: Heat dissipation type:
3=Air cooled; Commercial version
6=Conduction cooled; Reinforced Rugged version
The last two zeros are reserved selection slots for the factory, customized options based on actual applications.

K-JIANG
Add: Jimei North Road, Jimei District, Xiamen, Fujian, China
Tell:+86-15305925923