Eaton XV-102-L series industrial touch screen HMI

Eaton XV-102-L series industrial touch screen HMI

The official operation manual for Eaton XV-102-L series industrial touch screen HMI (optional integrated PLC), released in April 2024, covers three sizes of 3.5/5.7/7.0 inches, adopts resistive touch and 800MHz RISC processor, comes standard with Ethernet, USB, SD card interfaces, optional RS-232/485, CAN, supports CODESYS programming, meets UL, CE, DNV-GL classification, ATEX Zone 22 certification, and provides detailed instructions on safety specifications, installation wiring, debugging, interface definition, troubleshooting, and maintenance processes. It is suitable for industrial automation equipment monitoring and control.

Hardware configuration and specifications

1. Size and Display

Size resolution, appearance ratio, weight

3.5-inch 320 × 240 (QVGA) 4:3 0.3kg

5.7-inch 640 × 480 (VGA) 4:3 0.6kg

7.0 inch 800 × 480 (WVGA) 16:9 0.6kg

Display: 64k colors, brightness of 250cd/m ², LED backlight lifespan of 40000 hours

Touch: 4-wire resistive touch, supports finger/stylus operation

2. Core hardware

Processor: 32-bit RISC 800MHz

Memory: 512MB DRAM, 4GB built-in storage, 125KB NVRAM

Clock: Built in lithium battery backup, with a power outage endurance of 10 years (25 ℃)

3. Interface configuration (standard+optional)

Interface type specification

Ethernet 10/100Mbps, RJ45, CAT5e/6

USB Host USB 2.0，500mA， Non electrical isolation

SD card supports SD/SDHC, SDA 2.0

RS-232 9-pin D-Sub, non isolated

RS-485 9-pin D-Sub, non isolated, up to 1200m away

CAN 9-pin D-Sub, supporting CANopen/J1939

4. Electrical parameters

Power supply: 24VDC SELV/PELV, range 19.2~30.0VDC

Power consumption: 3.5 inches * * ≤ 5W * *; 5.7/7 inches * * ≤ 7W**

Protection: Built in fuse, reverse polarity protection, no electrical isolation

Starting impulse current: ≤ 1.5A ² s

Safety regulations (mandatory requirement)

Personnel qualifications: Only certified electricians who comply with EN 50110-1/-2 are allowed to operate

Before operation: Power must be cut off, hung, tested, grounded, and short circuited

Grounding: Functional grounding FE must be connected to protective grounding PE or equipotential connection

Taboo:

Prohibited for safety related functions (emergency stop, protection, etc.)

Prohibited for use in explosive environments (except Zone 22)

Prohibit live plugging and unplugging of communication interfaces

Static electricity: Release human static electricity before operation to prevent damage to components

Installation requirements

Installation method: Front embedded installation, available in landscape/portrait mode

Panel thickness: 2mm ≤ d ≤ 5mm, flatness ≤ 0.5mm

Fixed bracket:

3.5 inches: 4 pieces

5.7 inches: 6 pieces

7.0 inches: 8 pieces

Heat dissipation: natural convection, reserved ventilation space of * * ≥ 30mm * * around

environment

Operating temperature: 0~50 ℃

Storage temperature: -20~60 ℃

Humidity: 10%~95% RH, no condensation

Protection level: IP65 front, IP20 back, NEMA 4X/12

Wiring and Communication

Power wiring: 3-pin terminal,+24V/0V/FE, torque 0.6~0.8Nm

Communication cables: All use shielded cables, with the shielding layer grounded at one end

Ethernet: Maximum line length of 100m, to avoid stress and vibration

RS-485: up to 1200m, with 120 Ω terminal resistors connected at both ends

CAN: up to 5000m (low speed), with 120 Ω terminals at both ends

Debugging and Running

Power on start: No power switch, start immediately when powered on

Initial setup: Configure system parameters, install visualization/PLC software

Touch calibration: recalibration is required when abnormal response occurs

Storage: SD card can only be plugged and unplugged when power is off to avoid frequent writing

Malfunctions and Maintenance

1. Common faults

Cause and solution of fault phenomenon

Unable to power on without 24VDC, wiring error. Check power supply and polarity

Touch malfunction not calibrated, function off calibrated touch, function on enabled

Communication abnormal cable not shielded, poor grounding, replacement of shielded wire, standardized grounding

2. Maintenance and upkeep

Cleaning: Wipe with a soft cloth, prohibit sharp objects, solvents, and liquids from entering

Battery: Built in lithium battery, maintenance free, scrapped requires professional handling

Storage: Avoid light, moisture, and vibration, use original packaging

Certification and Compliance

Safety regulations: UL508, CE, IEC/EN 60950, IEC/EN 61131-2

Classification: DNV-GL (requires installation of power filter)

Explosion proof: ATEX Zone 22, II 3D Ex tc IIIC T70 ℃ IP6x

EMC: Industrial environment anti-interference, compliant with EN 61000-6-2/-4

Key issues

Question 1: What are the power supply requirements for the XV-102-L series? What protection will there be if the wrong connection is made?

Answer: The power supply is 24VDC SELV/PELV, with an effective range of 19.2~30.0VDC; The device is equipped with reverse polarity protection and built-in fuses. Connecting the positive and negative poles in reverse will not cause immediate damage, but it must be strictly wired according to the terminal definition.

Question 2: What are the fixation and protection requirements for the installation of this device?

Answer: Front embedded installation, panel thickness 2-5mm; 3.5/5.7/7 inches are fixed with 4/6/8 brackets respectively; Correctly installing the sealing ring can achieve the front IP65 protection and is only suitable for indoor dry environments.

Question 3: What is the maximum transmission distance supported by the communication interfaces of XV-102-L? What are the wiring requirements?

Answer: Ethernet 100m, RS-485 1200m, CAN up to 5000m (low-speed); All communication lines must use shielded cables, with the shielding layer grounded nearby to avoid being laid in the same cable tray as power lines.