Fuji FRENIC Mini Inverter

Fuji FRENIC Mini Inverter

Product Overview

Applicable Models

Three phase 200V: FRN0001~0020C2S-2 (0.1~3.7kW)

Three phase 400V: FRN0002~0011C2S-4 (0.4~3.7kW)

Single phase 200V: FRN0001~0012C2S-7 (0.1~2.2kW)

Core purpose

Small fan, water pump, conveyor belt, compressor, simple mechanical speed regulation

Support AMF self start stop, PID regulation, multi-stage speed, external terminal control, RS485 communication

Key Features

Small size, high protection, low cost, high reliability

Support V/F control, dynamic torque vector control, PMSM drive

Complete protection: prevention of overcurrent, overvoltage, undervoltage, overload, overheating, and stall

Panel buttons+potentiometer speed control, supporting external terminals and communication control

Safety regulations (mandatory reading)

Warning level

Warning: May cause death/serious injury

CAUTION: May cause minor injuries/equipment damage

Core taboos

Prohibited for use in single-phase motors and life support systems

Must be installed with metal and kept away from flammable materials

Grounding is required, and MCCB/ELCB circuit breakers must be added to the input

Do not connect the power supply to the output terminal U/V/W

Prohibit adding surge absorbers and compensating capacitors on the output side

Power off for at least 5 minutes and confirm that the DC voltage is less than 25V before disassembling the machine

The STOP button on the panel can be blocked and must be externally connected for emergency stop

Installation and Environment

Environmental Requirements

Temperature: -10~+50 ℃ (when there is no gap in parallel -10~+40 ℃)

Humidity: 5~95% RH (no condensation)

Altitude: ≤ 1000m (1000-3000m requires derating)

Protection: IP20, indoor installation, dustproof and oil proof

Installation spacing

Up and down: ≥ 100mm; left and right: ≥ 10mm

Multiple units can be arranged side by side without gaps; Stacking up and down requires the addition of insulation panels

Wiring (Core Chapter)

Main circuit terminal

Input: L1/R, L2/S, L3/T (three-phase)/L1/L, L2/N (single-phase)

Output: U, V, W → connected to motor

DC circuit: P (+), N (-), P1, DB (braking resistor)

Grounding: The G terminal must be grounded

control terminal

Digital inputs: FWD/REV, X1/X2/X3, CM, PLC

Analog inputs: 12 (0-10V), C1 (4-20mA), 11 (AGND)

Analog output: FMA (0-10V)

Transistor output: Y1, Y1E

Relay output: 30A/30B/30C

Communication: RJ-45 (RS485)

Wiring rules

The input power must be connected to L1/L2/L3, and it is strictly prohibited to connect to U/V/W

Motor wire ≤ 50m, extra long requires an output filter OFL

Separate the wiring of the main circuit and control line, and ground the shielded wire

Power supply ≥ 500kVA must be connected to DC reactor DCR

The braking resistor should only be connected to P (+) - DB, and it is strictly prohibited to connect to P-N

Jumper settings

SW1: Digital Input SINK/Source Switching

SW3: RS485 terminal resistor ON/OFF

Panel operation (three major modes)

Panel buttons

RUN: Run

STOP: Stop

PRG/RESET: Programming/Reset

FUNC/DATA: Function/Data

▲/▼: Parameter adjustment

three modes

Operation mode: monitoring frequency, current, voltage PID

Programming mode: parameter setting, data check, I/O check, alarm query, maintenance information

Alarm mode: Fault code display, historical records, fault data

Common Operations

Potentiometer: direct speed regulation

▲/▼: Digital setting frequency

PRG → Enter Parameters

STOP+▲: Jogging mode

Function code system (8 categories)

1) F-code: Basic functions (most commonly used)

F01: Frequency command source (panel/potentiometer/terminal/communication)

F02: Running instruction source (panel/terminal)

F03: Maximum frequency

F04: Reference frequency

F05: Reference voltage

F07/F08: Acceleration and deceleration time

F09: Torque Enhancement

F10-F12: Electronic thermal relay (motor overload protection)

F14: Power outage restart mode

F20-F22: DC braking

F26: Carrier frequency (noise reduction)

F42: Control mode (V/F/vector/PMSM)

2) E code: Terminal function

E01-E03: X1-X2-X3 Function Definition (Multi speed, Reset, Jogging, DC Braking, etc.)

E20/E27: Y1/30A Output Definition (Running, Frequency Arrival, Alarm, Overload Warning)

E52: Panel menu mode (simple/full function)

3) C code: frequency control

C01-C99: Jump frequency, multi-stage speed (16 stages), jog frequency PID

4) P code: Motor 1 parameters

P02-P03: Motor capacity/rated current

P04: Automatic tuning (stationary/rotating)

P60-P63: PMSM permanent magnet synchronous motor parameters

5) H-code: Advanced Features

Automatic reset, fan control, S-curve acceleration and deceleration, instantaneous power outage restart, maintenance timer

6) A code: Motor 2 parameters (dual motor switching)

7) J code: Application Function (PID)

J01: PID Enable

J03-J05: PID proportional/integral/derivative

8) Y-code: Communication (RS485)

Y01: Station number; Y04: Baud rate; Y10: Protocol (Modbus RTU)

Run and debug

Test steps

Confirm correct wiring and reliable grounding

Set the rated parameters of the motor (F04/F05/P02/P03)

Set acceleration and deceleration time

Low speed (5Hz) test run, confirm steering

Gradually increase the speed and check for vibration/noise/current

Automatic tuning (P04)

Mode 1: Static tuning (resistance/leakage impedance)

Mode 2: Rotation tuning (no-load current/slip)

It is essential to adapt to third-party motors.

Protection function (alarm and trip)

Main alarm code

OC: Overcurrent

OV: Overvoltage

LU: Undervoltage

OH: Overheating of heat sink

OL: Motor overload

EF: External malfunction

Erx: Communication/parameter error

Third level action

Warning: Do not stop the machine

Uninstalling: Jumping output without interruption

Alarm: Shutdown and Trip

Maintenance and Inspection

routine inspection

Temperature, noise, vibration, cooling fan, terminal fastening

Regularly replace parts

Electrolytic capacitors, cooling fans, relays

insulation test

Use a 500V megohmmeter, perform disassembly testing, and prohibit online testing

Standards and Certification

Compliant with the EU LV Low Voltage Directive and EMC Directive

Harmonic suppression suggestion: Install DC reactor DCR

It is recommended to use B-type or high-frequency corresponding type for leakage protection devices

Typical application configuration

Panel control: F01=4 (potentiometer), F02=2 (forward rotation)

Terminal two speed: X1=SS1, C05=30Hz, C06=50Hz

PID constant pressure water supply: J01=1, C1=4-20mA feedback

RS485 Modbus：y01=1，y04=9600，y10=0

Braking and parking: DB is connected to the braking resistor, F20=0.5Hz，F21=50%