GE IC693MDL655 Discrete Input Module

GE IC693MDL655 Discrete Input Module

Product Core Basic Information and Positioning

Basic identification and functional positioning

Specific project content

Ordering Number IC693MDL655 (core ordering identifier, belonging to the I/O module series of GE Series 90-30 PLC)

Product Type 24V DC Positive and Negative Logic Discrete Input Module

The core function is to collect 32 discrete signals from industrial sites (such as on/off signals from sensors, limit switches, buttons, etc.), isolate them through optocouplers, and transmit them to the PLC logic side to achieve safe interaction between on-site signals and control systems

The adaptation system is only compatible with GE Series 90-30 PLC systems and can be installed in any I/O slot of the 5-slot or 10 slot baseboard

‍

Key functional characteristics and electrical parameters

1. Core functional features

Input channel configuration: There are a total of 32 discrete inputs, divided into 4 independent isolation groups (A1-A8, B1-B8, C1 to C8, D1 to D8), with 8 inputs in each group. Each group has an independent common terminal (ACOM, BCOM, CCOM, DCOM) to avoid signal interference between groups;

Isolation design:

The on-site side and logic side are isolated by a photoelectric coupler to achieve 1500V, protecting the PLC core circuit from high-voltage/interference effects on site;

The isolation voltage between groups is 250V, further reducing signal crosstalk between different input groups;

Status indication: The top of the module is equipped with 32 LED indicator lights (corresponding to A1-A8 to D1-D8), which display the real-time on-off status (ON/OFF) of each input for easy troubleshooting;

Logical compatibility: Supports positive and negative logic inputs, adapts to field signals of different polarities, can withstand up to 30V DC input voltage, and adapts to fluctuations in industrial power grids.

2. Key electrical parameters

Parameter category specific specifications

Input voltage - rated voltage: 24V DC (positive and negative logic);

-Input range: 0~30V DC;

-On state voltage: 11.5~30V DC;

-Off state Voltage: 0~5V DC

Input current - typical conduction current (at 24V DC): 7.0mA;

-Minimum conduction current: 3.2mA;

-Maximum shutdown current: 1.1mA

Response time - On response time: maximum 2ms;

-Off response time: up to 2ms, meeting the requirements of fast signal acquisition

Power consumption - Backboard+5V bus power consumption: maximum 195mA (including 29mA basic power consumption+0.5mA per channel conduction+4.7mA per channel LED lighting);

-Isolation 24V bus/user power consumption (24V DC, 32 fully conductive): typical 224mA

The maximum number of conductive input channels for temperature characteristics varies with the ambient temperature (such as 8 channels per group can be fully conductive at 35 ℃, and only 2 channels per group can be conductive at 60 ℃), and the load configuration needs to be adjusted according to the actual ambient temperature

Installation and wiring information

1. Installation requirements

Installation position: It can only be installed in any I/O slot of the GE Series 90-30 PLC's 5-slot or 10 slot baseboard, without special slot restrictions;

Environmental conditions: Must meet industrial environmental requirements (temperature, humidity, etc. refer to the overall specifications of the PLC system), avoiding high temperature, high humidity, and strong electromagnetic interference scenarios.

2. Wiring configuration

Connector type: The module is equipped with two 24 pin male connectors (Fujitsu FCN-365P024-AU) on the front, with the right connector corresponding to Group A and B inputs, and the left connector corresponding to Group C and D inputs;

Cable selection:

Recommend using GE original pre wired cables, models IC693CBL327 and IC693CBL328 (one end is a matching female head, and the other end is a stripped tin plated wire);

You can also make cables yourself, please refer to Appendix C of the document for the "24 pin connector cable production guide" (IC693CBL327/328 data sheet);

Power supply method: The on-site equipment power supply can be provided by the user themselves, or an isolated 24V DC output power supply can be used on the module I/O connector;

Wiring logic: Each input group needs to be connected to the corresponding common terminal (such as A group connected to ACOM, B group connected to BCOM), and the positive and negative logic is achieved through power polarity switching. For specific wiring, please refer to Figure 6-20 in the document (on-site wiring diagram).

3. Wiring table (core grouping)

The document provides detailed wiring tables for A/B group (right connector) and C/D group (left connector), specifying module points, connector pins, cable pairs, and color coding. The following are examples of key corresponding relationships:

Function Description of Cable Color Matching for Pin Connectors of Grouping Modules

Group A A1 A1 1 Brown Input Signal A1

Group A ACOM A5 3 Orange Group A Common Terminal

B group B1 B1 7 purple input signal B1

Group B BCOM B8 10 Pink/Black Group B Public End

Power supply+24V OUT B6 9 gray/black isolated 24V output

Power supply 0V A7 4 yellow power supply ground