K-WANG

+086-15305925923
Service expert in industrial control field!
NameDescriptionContent
Adequate Inventory, Timely Service
pursuit of excellence 
Ship control system
Equipment control system
Power monitoring system
Current position:
新闻动态
newS
   
Brand

KUKA KR 300 R2700-2 C-F Cast Ceiling Mounted 6-Axis Heavy duty Industrial Robot

From: | Author:Wang | Time :2026-09-14 | 243 visit: | 🔊 Click to read aloud ❚❚ ▶ | Share:

KUKA KR 300 R2700-2 C-F Cast Ceiling Mounted 6-Axis Heavy duty Industrial Robot

The official English original assembly manual for the body assembly, safety, technical parameters, transportation, debugging, maintenance, repair, and disposal of the cast ceiling mounted 6-axis heavy-duty industrial robot KR 300 R2700-2 C-F, compatible with KR C4/KR C5 controllers; The suffix C=Ceiling installation, F=Foundry casting environment version, with dust and coolant resistance, and casting specific positive pressure blowing function.

Product Description

Robot system composition: robotic arm body, controller, connecting cables, teaching pendant, software, tools and options.

The six major assemblies of the robotic arm body are: inline wrist, boom, connecting rod arm, hydraulic nitrogen balance system, rotating column, and base frame.

A1-A3 is equipped with mechanical terminal blocks for equipment protection only; Personnel protection relies on SafeRobot software or optional mechanical axis limit.

Balance system: Installed between the rotating column and the connecting rod arm, it belongs to Class I pressure equipment and consists of an accumulator, hydraulic cylinder, and explosion-proof plate to counteract the A2 axis gravity torque.

The wrist is a 3-axis straight row wrist, and the A6 motor is built into the upper arm; A4/A5 are driven by connecting the drive shaft.

All motor cables and signal cables use quick plug connectors, and the base is integrated with an RDC box.

Expected use and prohibition of misuse

Allow: tools for handling and handling workpieces, casting conditions; Environmental conditions and maintenance cycles must be followed.

Prohibited: climbing, carrying people and animals, outdoors, explosion-proof areas, radioactive environments, underground mining; Unauthorized use results in loss of warranty.

Robots belong to partially completed machinery and must be integrated into a complete set of CE compliant equipment before they can be put into operation.

Available options: brake release device, A1 hollow shaft cover, cable package cover, 4 blowing options A/B/C/D, mechanical shaft limit, energy supply pipeline package, etc.


Safety Regulations

This chapter focuses on the mechanical arm body; When paired with KUKA controllers, it is also necessary to read the controller safety chapter.

Disclaimer and EC Machinery Directive: Robots provide an 'Integration Declaration'; The system integrator is responsible for the risk assessment of the entire system, issuing EC compliance statements, and affixing CE markings. It is prohibited to modify robots without authorization from KUKA. Any damage caused by third-party accessories shall be borne by the user; Even if all safety instructions are followed, it is impossible to completely eliminate personal injury and equipment damage.

personnel qualification

User: Implement labor safety, personnel supervision, and regular training;

Integrator: responsible for installing wiring, risk assessment, safety protection, and compiling system operation manuals;

Operator/maintenance personnel: Read all manuals thoroughly and pass professional training.

Area definition: Hazardous area=robot workspace+robotic arm+external axis stopping distance, must be physically protected; If there is no physical protection, the EN ISO 10218 collaborative robot standard shall be implemented.

Protective equipment: mechanical terminal block, optional A1-A3 mechanical shaft limit, release device, hazard warning nameplate; The nameplate is prohibited from being painted or removed.

Safety measures for various working conditions

General: If the controller is powered off, the robotic arm will still fall due to brake failure. It is strictly prohibited for personnel to stand under the arm; High temperature operation of the motor; Personnel wearing active implantable devices such as pacemakers must be at least 300mm away from the motor/brake; emergency stop failure occurs when the teaching pendant is disconnected; After modifying the robot, all safety functions must be fully tested; Immediately cut off power, lock and tag out the fault.

Transportation: The designated transportation posture must be maintained to avoid impact and vibration.

Start debugging: Change the default password of the controller; The robotic arm can only be matched with the corresponding model controller; Prevent condensation; Check for invisible collision damage before starting up; Complete testing of the safety circuit.

Manual mode: New/modified programs must undergo T1 (≤ 250 mm/s) testing; T2 high-speed mode is only used for testing, and the operator must be outside the danger zone.

Automatic mode: All safety devices are intact, and the danger zone is unmanned or meets the cooperation standards.

Maintenance and repair: power off and lock; Wait for several minutes for high-voltage components to discharge after power failure; The balance system operation must be mechanically locked with the arm body in advance; Refer to MSDS Chemical Safety Data Sheet for handling oil.

Discontinue storage disposal: comply with local laws and regulations.


Technical Data

Basic parameters of the ontology

Project KR 300 R2700-2 C-F

6 axes fully controlled

Rated load of 300 kg; maximum load of 366 kg

Maximum reach distance 2671mm

Repetitive positioning accuracy ISO9283 ± 0.05   mm

The self weight of the body is about 1105 kg

Protection level: IP65 for the main body; Wrist IP67

Noise<75 dB (A)

The installation method is only for ceiling installation, with a tilt angle of ± 0 °

Controller compatible with KR C4/KR C5 M6/M7

Casting plate special internal 0.3 bar positive pressure blowing, compressed air ISO8573-1, wrist short-term high temperature resistance of 180 ℃

Operating at an ambient temperature of 0-55 ℃; Storage -40~60 ℃

Axis motion parameters

Motion range: A1 ± 185 °; A2‑140°~‑14°; A3‑120°~+168°; A4/A6 ±350°; A5 ±122.5°

Maximum shaft speed under rated load: A1 105 °/s; A2 101 °/s; A3 107 °/s; A4 140 °/s; A5 113 °/s; A6 180 °/s

Load capacity: Provide wrist flange ZH300 parameters (flange diameter 160mm, M10-10.9 bolts); Load center of gravity, moment of inertia, load curve diagram; Distinguish between normal operation and emergency stop conditions, where the flange is subjected to axial force, radial force, overturning moment, and torsional moment; Additional loads are allowed to be added to the boom, connecting rod arm, and rotating column.

Base load (ceiling working condition): Provide vertical force, horizontal force, overturning moment, A1 torque, divided into normal working condition and emergency stop maximum value; The steel structure base must be structurally checked according to the maximum value, otherwise there is a risk of the robot falling.

Cable parameters: distinguish between KR C4 and KR C5 cable definitions; The standard length of motor cables and data cables is 7-50 meters, with a maximum total length of 50 meters, and a maximum extension allowed once; It is necessary to independently protect the grounding; Provide the pin diagram for the A1 base interface.

Stop distance and stop time: distinguish between STOP0 (cutting off the brake) and STOP1 safe stop; Provide stop angle and stop time charts for A1-A3 under different stretching ratios, loads, and program magnification POV; The brake has wear and tear, it is recommended to review the stopping distance annually.

Nameplate labels, REACH regulation information, and two-dimensional drawings of work envelopes.

Planning and Design

Accelerated wear conditions: long-term temperature limit operation, abrasive dust environment, continuous approach to performance limit, single axis high duty cycle, short cycle reciprocating motion, external process forces; If the above working conditions occur, it is necessary to consult KUKA to shorten the maintenance cycle.

Rack mounted installation: The robot ceiling must use rack mounted components, including 8 M24 bolts and positioning pins; Strict requirements are given for the flatness, roughness, and stiffness of the installation base.

Cable planning: The minimum static bending radius for motor cables is 150   mm, and for signal cables it is 60   mm. Motor cables and data cables are laid separately in metal cable trays to achieve EMC electromagnetic compatibility; Double grounding; Cable layout eliminates the risk of tripping.


Transportation

Forced transportation posture (maintained throughout the entire transportation process): A1=0 °, A2=-137 °, A3=160 °, A4=0 °, A5=-105 °, A6=0 °. It is not allowed to change the posture without fixing the base to prevent overturning.

Shipping Method

Forklift: The base comes with a fork groove, and the minimum rated load of the forklift is 2 tons;

Crane: KUKA specialized lifting equipment is selected, with lifting points distributed on rotating columns and base fork slots; The lifting chain must be adjusted to ensure that the robot is suspended vertically.

Transportation prohibits non-standard lifting points; Avoid impact and vibration throughout the transportation process; Transport completed and lifting equipment removed. Provide the overall dimensions and center of gravity position for the transportation of the entire machine.


Startup Debugging and Restarting

This robot adopts a rack mounted ceiling installation, and the key process points are:

Prerequisite: The robot is in a transport position, the steel structure base is completed, and the lifting equipment is in place.

Installation Steps

Clean the interface between the base and the robot, and install the positioning pin;

The crane vertically lifts the robot into position to prevent damage to the positioning pin from collision;

Tighten 8 M24 bolts diagonally in multiple stages to the specified torque;

Connect dual protection grounding (torque 23 Nm);

Connect motor cables XD30/X30 and data cables XF31/X31 for KR-C4 and KR-C5 respectively; Confirm that the connector lock is in place;

Complete controller configuration and set the robot ceiling installation posture;

Install tools and complete the overall power on debugging according to the controller manual; There is a risk of air accumulation after balancing the system storage, and the A2 axis swings slightly to release the air from the pressure relief valve.

Provide complete wiring diagrams for motor cables, data cables, and grounding cables of KR-C4 and KR-C5.


Maintenance

Only maintenance projects recorded in this document can be executed; The remaining repairs will be handed over to KUKA training personnel; The maintenance cycle is shortened when the oil temperature is above 60 ℃; Emergency stop and lock before maintenance.

Maintenance cycle summary table

Periodic homework content consumables

After being put into operation, only one 100 hour recheck of the base bolt torque is required

Add LGEP2 grease to two bearings of the balance system at 2500 hours or at the latest 1 year; Check the balance system nitrogen pressure LGEP 2 lubricating grease, Hyspin ZZ46 hydraulic oil

10000   h or at the latest 5 years, all gearboxes of A1-A6 should be replaced with Optigear Synt. ALR 150 gear oil; Oil filling amount for each axis A1=8.30   L; A2=2.10   L; A3=1.40   L; A4=2.10   L; A5/A6=1.90   L

Replace the entire balance system with the original balance cylinder assembly in 10 years

7 years or changes in working conditions, it is recommended that KUKA conduct on-site inspection of the entire machine.

Key maintenance process

General rules for gearbox oil change: The gearbox needs to be at operating temperature; Measure the actual amount of oil released during oil discharge; If the oil release rate is less than 70% of the rated value, the gearbox must be flushed; Rinse twice below 50%, and move the entire stroke during rinsing; Magnetic plug inspection for metal debris; Oil change completed T1 mode jog operation, check for leaks. The ceiling robot A1 has a special oil discharge and injection pipeline, which is operated from the base interface.

Balance system maintenance (high-risk pressure components)

Pressure detection: The minimum pressure in an environment at 20 ℃ is 244.8 bar. If it is lower than this value, the entire balance system must be replaced;

Replacing the balance system: To replace the balance cylinder of the suspended ceiling robot, the robot must first be disassembled and fixed to the ground; Use a sling to secure the connecting rod arm throughout the entire homework process; The complete process of pressure relief, disassembly, installation, and recharging. The weight of the balance system is about 40 kg, with high-pressure oil and gas inside. Unauthorized personnel are strictly prohibited from disassembling it.

Robot cleaning: Do not use high-pressure water guns or compressed air to blow the bearing seals; Use solvent-free water-soluble neutral cleaning agents; Power off operation to prevent liquid from entering the motor gearbox.


Maintenance

The manual provides detailed steps for replacing A1-A6 motors, straight row wrist assemblies, and connecting drive shafts.

General safety for motor replacement: power off, lock the main switch, wait for 5 minutes for high voltage discharge; Before disassembling the motor, the corresponding shaft must be locked with a sling/fixture to prevent the arm from falling; Dismantle the old motor, check that the involute spline is not damaged, and evenly apply Microlube GL261 grease; O-rings and seals must be inspected and replaced if damaged; Tighten the bolts diagonally in steps; After the motor installation is completed, the axis must undergo Mastering zero calibration and T1 mode trial operation.

Special difficulties:

Dismantling of A2/A3 motors requires fixing the connecting rod arm/boom with a sling to prevent the balance system from falling after unloading;

A6 motor: It is necessary to first remove the A4 and A5 motors, and then remove the entire straight row wrist before removing the A6 motor;

To replace the straight row wrist assembly and transmission shaft, it is necessary to sequentially remove the A4/A5 motors and disassemble the wrist.

Overview of electrical wiring, definition of connectors; Repairs must use KUKA original spare parts; Verify all safety functions after repair.


Suspension, Storage, and Disposal

Shutdown disassembly: Move the robot to the transport position; Install lifting equipment; Disconnect all cables; Lift the crane off the robot body.

Storage: Maintain transportation posture, clean the robot, take rust prevention measures, and meet temperature and humidity storage conditions.

Scrap disposal: Lubricating oil, hydraulic oil, electronic components, and metal structures shall be classified and disposed of in accordance with local environmental regulations.


Options

Release device: manually move the robotic arm in power-off state; Operation steps and safety requirements.

A1 hollow shaft cover; Cable wrap cover.

Foundry Casting Edition 4 sets of blowing options A/B/C/D: Inject dry compressed air into the interior of the robot to maintain positive internal pressure and prevent dust and casting coolant from entering the interior.

  • GE 369B1860G0026 MPU50 Nexus Controller
  • GE IS420ESWBH3A Industrial ESWB Ethernet Switch
  • GE IS420ESWBH2A Mark VIe IONet Network Switch
  • GE IS200SRTDH2ACB RTD Terminal Board Mark VI
  • GE SR469-P5-HI-A20 Motor Protection Relay
  • GE VMIVME-7750 Pentium III VME CPU Module
  • GE IS215UCVEH2AE VMIVME-7614-132 VME Controller Card
  • GE MVDL800-47931101-A Liquid-Cooled Delta Module for MV3000 Medium Voltage Drive Systems
  • ABB BRC410 SPBRC410 Harmony Bridge Controller
  • ABB PFCL201CE-50kN 3BSE006699D0005 Pressductor PillowBlock Load Cell
  • ABB 5SHY3545L0009 3BHB013085R0001 IGCT Module
  • Wika IPT10 - Process Pressure Transmitter
  • Omron SK20-C1DT-D - Programmable Controller PLC Unit
  • Foxboro Eckardt (Schneider) AE214 - Field Indicator Digital Display Meter
  • Omron CJ1W-OD232 - Transistor Output Unit PLC Module
  • Jetter JX2-IO16 - Digital Input Output Module PLC
  • SEFI ACS 48.6A-NS - Power Supply Unit
  • Schneider (Telemecanique) XBTF011110 - Magelis Membrane Keyboard Overlay
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Siemens 6SL3120-2TE13-0AA3 - Sinamics S120 Dual Motor Module Inverter
  • SEW Eurodrive MAS51A005-503-50 - Movidyn Servo Drive Controller
  • Record ATE 20 - Automatic Door Brake Motor
  • Record ATE STA 21 - Automatic Door Brake Motor
  • Sanyo Denki R2AA06040FXP02 - AC Servo Motor
  • Omron NX-ID4442 - DC Digital Input Unit PLC Module
  • Schneider (Telemecanique) XBTGT2330 - Magelis Advanced Touch Panel HMI
  • ABB DX561-A1 - AC500 Digital Input Output PLC Module
  • SEW Eurodrive MC07B0004-2A3-4-00 - Movitrac B AC Frequency Inverter Drive
  • Schneider (Telemecanique) FT20CBCL030 - Connection Communication Cable
  • Visions AXFR 600601 - Gap Control Side Board PCBA
  • Allen Bradley 1797-CEC-A-C01 - Flex Ex Communication Interface Adapter
  • Siemens 6ES5095-8MC03 - Simatic S5 Programmable Controller CPU
  • Tectrol / Pitney Bowes TC53S-1392 - Power Supply Unit
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Neste 0635-107 - Control Board for SLX Automatic Sliding Door
  • RSF Elektronik MS 2x.x4 MO - Linear Encoder Sensor
  • Pro-face GP37W2-BG41-24V - Graphic Terminal Operator Panel HMI
  • Allen Bradley 2711P-RP1 - PanelView Plus Logic Module HMI
  • ABB (Asea Brown Boveri) GNT0144700R0004 - Power Supply Electronic Board Module
  • SEW Eurodrive MC-LTE-B-0008-2B1-1-40 - Movitrac LTE AC Frequency Inverter Drive
  • Siemens 3RK1301-0AB10-0AA4 - Direct Starter Modular Motor Starter
  • Yaskawa SGDB-15VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9421 - 8-Channel C Series Digital Input Module
  • Yaskawa SGDB-10VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9476 - 32-Channel C Series Source Digital Output Module
  • Pitney Bowes R782000 - Turbojet Controller Board PCBA
  • Lika IT65-Y-1000BND2 - Incremental Encoder Sensor
  • Came 002ZT6 - Control Panel Board for Gear Motors
  • Desin HS-300/7500 - Multivariable Process Controller Unit
  • Pilz PNOZ mc1p - Modular Safety Relay Controller
  • Innovative Robotics PTNR2-2-NES - Controller Interface Board Module
  • Schneider Electric (Telemecanique) TSXCB4020 - Printer Communication Link Cable
  • Wika IPT10 - Process Pressure Transmitter
  • Schneider Electric (Modicon) TSXDMF342A - Extension Digital Analog Module for TSX17 PLC
  • Omron F150-KP - Vision System Cursor Key Pack Console
  • National Instruments BNC-2110 - Shielded Connector Block Accessory
  • Bosch Rexroth (Indramat) CSH01.2C-SE-EN2-EN2-CCD-NN-S-FW - Servo Drive Control Panel Interface Module
  • GHM / Gefran / Baumer GHM510573A/1000 - Incremental Encoder Sensor
  • National Instruments NI 9425 - 32-Channel C Series Digital Input Module
  • Schneider (Telemecanique) STBDDO3705 - Digital Output Module STB
  • Siemens 6EP1436-1SH01 - Regulated Power Supply Unit
  • Schneider Electric (Modicon) TSXFPP20 - Fipway PCMCIA Communication Board
  • April QMB 3202 - PLC Output Card Module with Parameter Surveillance
  • Siemens 6ES5240-1AA12 - Simatic S5 Communication Processor Module
  • Midi Engineering MI907A - Stepper Motor Midi Amplifier Driver
  • Schneider Electric (Telemecanique) TSXAEZ414 - TSX Series Analog Input Module
  • Schneider (Telemecanique) TSX17-20 - TSX17 Compact PLC Controller Unit
  • Siemens 6ES5955-3LC14 - Simatic S5 Modular Power Supply Unit
  • Schneider (Telemecanique) ATV66U72N4 - Altivar 66 AC Frequency Inverter Drive
  • Omron NX-OD4256 - Transistor Output Unit PLC Module
  • Yaskawa / Omron SGDH-04AE-OY - Sigma II Servo Drive 400W
  • RSF Elektronik MS 20.04-2M - Linear Encoder Scale Sensor
  • ITT GMW (Metrosx) DAA288-240 A - LED Message Display Board
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Sensorex Alpha-LSE - Display Inclinometer Indicator
  • Omron NX-DA3603 - Analog Output Unit PLC Module
  • Grundig Electronic NRP 02 - Power Supply Control Unit Module
  • ProSoft Technology RLX-FHES-F - RadioLinx Industrial Wireless Hotspot Router
  • Omron NX-EIC202 - EtherCAT Coupler Unit PLC Module
  • Omron NX-TS3201 - Temperature Sensor Input Unit PLC Module
  • Omron CQM1-CPU41-V1 - Sysmac CQM1 PLC CPU System
  • April CPU5001 - PLC CPU Processing Unit
  • Yaskawa JZDP-D008-020-E - Linear Servo Motor Actuator
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 2711-K3A17L - PanelView 300 Operator Terminal HMI
  • Schneider (Telemecanique) TSXAEM411 - TSX Series Analog Input Module
  • Schneider Electric (Telemecanique) XBTGT5330 - Magelis Advanced Touch Panel HMI
  • Siemens 6ES5928-3UA12 - Simatic S5 Central Processing Unit PLC
  • Schneider (Telemecanique) TSXSUP65 - Power Supply Module
  • Schneider (Telemecanique) TSXLES61 + TSXLES60 - TSX Series Fine Line Box Local Module
  • Siemens 6SE6440-2AD23-0BA1 - Micromaster 440 AC Frequency Inverter Drive
  • National Instruments NI 9205 - 32-Channel C Series Analog Input Module
  • Yaskawa CIMR-PCC42P2 - Varispeed AC Frequency Inverter Drive
  • ABB PM554-T-A1 - AC500 PLC CPU Module
  • National Instruments cDAQ-9178 - 8-Slot CompactDAQ USB Chassis Backplane
  • Allen Bradley 1786-RPA - ControlNet Repeater Adapter Module
  • Allen Bradley 1770-KFD - DH-485 Communication Interface Module
  • Grundig Electronic NSP 02 - Power Supply Control Unit Module
  • Teq Q07.K3S.002A - Control Panel Logic Board
  • Allen Bradley 1300-ITSSC - Signal Converter Interface Module
  • Omron CQM1H-CPU51 - CQM1H Modular PLC System
  • ProSoft Technology 4207-DFNT-MCM - ProLinx Industrial Gateway Module
  • Schneider Electric TSXSCP114 - RS485 PCMCIA Communication Board
  • Grundig NGE 01 - Power Supply Unit
  • Grundig NZP 03 - Power Supply Unit
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Danaher / Atlas Copco / Socapel SAM-PA-400-30-E - Servo Power Supply Controller Unit
  • Klöckner Moeller EM4-101-DD1 - Easy Control Relay Module
  • Bosch Rexroth DKC-10.3-012-3-MGP-01VRS - Indramat Digital Servo Controller Drive
  • Schneider (Telemecanique) XBTGT2110 - Magelis Touch Panel HMI with Cutter
  • Berger Lahr (Sig Positec) WD3-004.1802 - Stepper Motor Controller Driver
  • ProSoft Technology MVI56-WA-EIP - ControlLogix Wireless EtherNet/IP Communication Module
  • Allen Bradley 1794-ACNR15 - Flex I/O ControlNet Adapter Module
  • Fanuc A06B-6096-H201 - Servo Amplifier Module
  • Panasonic MSDA083A1 - AC Servo Driver Amplifier
  • Teq Q07.K3P.003B - Control Panel Logic Board
  • Schneider (Telemecanique) XBTH002010 - Magelis Operator Terminal HMI
  • Wika IPT10 - Process Pressure Transmitter
  • Teq Q07.A4P.001A - Control Panel I/O Module Board
  • Teq Q07.A3L.003A - Control Panel Module I/O Board
  • Siemens 6ES5246-4UA31 - Simatic S5 Positioning Module
  • Mitsubishi / Harmonic Drive HC-KFS43 - AC Servo Motor with Harmonic Reducer
  • Mitsubishi HC-KFS43 - AC Servo Motor
  • SES Store Electronic Systems 37120/120 - VLF Radio Transmitter Label System
  • Siemens 6SE9213-6BA40 - Micromaster AC Frequency Inverter Drive
  • Rosemount 1151DP5S22 - Differential Pressure Transmitter
  • Siemens 6FM1470-4AA20 - Simatic FM 470 Positioning Module Processor