K-WANG

+086-15305925923
Service expert in industrial control field!
NameDescriptionContent
Adequate Inventory, Timely Service
pursuit of excellence 
Ship control system
Equipment control system
Power monitoring system
Current position:
新闻动态
newS
   
Brand

KUKA KR IONTEC HO Robot Assembly Manual

From: | Author:Wang | Time :2026-09-15 | 162 visit: | 🔊 Click to read aloud ❚❚ ▶ | Share:

KUKA KR IONTEC HO Robot Assembly Manual

The assembly manual for KUKA KR IONTEC HO series sanitary oil lubricated six axis industrial robots covers three models: KR 50 R2100 HO, KR 50 R2500 HO, and KR 70 R2100 HO. It includes product instructions, safety specifications, technical parameters, planning and installation, transportation, commissioning and start-up, maintenance, repair, retirement storage and disposal, options, appendices, and all other contents. HO stands for Sanitary Oil, targeting the secondary food industry. The gearbox uses specialized Optileb GT 1800/460 lubricating oil.

Product Description

Composition of Robot System

Robot arm body, connecting cables, robot controllers (KR C4/KR C5), smartPAD teaching pendant, software, optional accessories. All three models are 6-axis serial joint robots, with main components including built-in wrist, linkage arm, rotating column, base frame, and electrical components. A1-A3 with mechanical end stop, only for equipment protection; Personnel safety relies on the Safe Robot function of the controller or optional mechanical axis limit.

Installation Form

Support ground, wall mounted, suspended ceiling, and installation at any tilt angle of 0-180 °; When not installed on the ground, the tilt angle must be configured in the WorkVisual software. Incorrect settings can cause overload and abnormal motion.

Prohibited misuse scenarios

Prohibit climbing and trampling, operating beyond parameters, direct contact with food, lack of safety equipment, carrying people and animals, outdoor use, explosion-proof areas, radioactive environments, and underground mining; Misuse will result in loss of warranty.

Wrist flange

Cast flange D=100, hole diameter 100   mm, 9 M8-10.9 threads, engagement depth 14-20   mm, locating pin Φ 8   H7, following ISO 9409-1.


Core Technical Data

KR 50 R2100 HO

Rated load of 50 kg, maximum load of 61 kg (requires KUKA verification of load conditions); The self weight is about 533 kg; the repeatability accuracy is ± 0.05 mm; the working envelope volume is 36 m ³.

Range of motion for each axis: A1 ± 185 °; A2‑175°~+60°; A3‑120°~+165°; A4 ±180°; A5 ±125°; A6 ± 350 °.

Maximum speed of each axis under rated load: A1 180 °/s, A2 175 °/s, A3 175 °/s, A4 250 °/s, A5 250 °/s, A6 360 °/s.

KR 50 R2500 HO

Rated load of 50 kg, maximum load of 61 kg, extended working radius; The range of axial motion is the same as KR50 R2100 HO.

KR 70 R2100 HO

Rated load of 70 kg, maximum load of 85 kg; A1-A3 have the same stroke, but the maximum shaft speed decreases: A2 158 °/s, A3 160 °/s, A4/A5 230 °/s, A6 320 °/s.

Environmental conditions

Operating temperature: 0~55 ℃; Storage and transportation -40~60 ℃;

Cable: Supports KR C4 and KR C5 controllers; Motor cables, data cables, 16mm ² equipotential grounding conductors; The cable length can be selected from 7-50 meters, with a maximum length of 50 meters.

Stopping distance and stopping time

Following DIN EN ISO 10218-1, distinguish between STOP   0 (category 0, uncontrolled emergency stop) and STOP   1 (category 1 controlled stop); Composite axis motion will increase the stopping distance; The manual provides charts of stop angles and stop times for each axis under different extension lengths, loads, and program magnifications of POV; The STOP   0 value is a simulation+test reference value, and it is recommended to conduct actual testing under actual project conditions.

Basic Load

The robot outputs force and torque to the base during motion, and the manual provides the force parameters of the base; The additional load of A1 rotating column and A2 connecting rod arm is not included in the factory foundation load. When calculating the foundation, an additional vertical force Fv must be added. The minimum grade of foundation concrete is C20/25.


Planning

Two installation options:

R300 × 400 (part number 0000-309-857, approximately 26.7 kg) with centering base kit: used for concrete foundation, including base plate, locating pin, M20 bolt, chemical anchor bolt; Insufficient flatness of the foundation requires the use of leveling mortar, and attention should be paid to not filling the bolt holes with mortar.

Rack mounted installation (0000-331-410, approximately 2.3 kg): Install directly onto the customer's steel structure and slide table adapter plate, relying on cylindrical and flat pins for positioning, and tighten 8 M20 bolts diagonally in multiple steps.

Warning: Installing the wrong robot may cause it to overturn. The integrator ensures the stability of the entire machine. Provide the base size diagram, concrete edge distance, and reinforcement requirements for reinforcing bars.


Transportation

Mode of transport

Forklift transportation: Use fork slots on both sides of the column, with a minimum load capacity of 2 tons for the forklift; Crane lifting: use approved M12 lifting points; The robot must first be moved to the designated transport posture, and the manual provides the center of gravity coordinates for each model; Prohibit the use of non certified lifting equipment.

Startup and Re Debugging

Startup process for two types of installations

1) Installation process of the base kit: Install the fork groove lifting device → Place the forklift in place → Install the positioning pin and bottom plate bolt → Adjust the level and perform leveling grouting if necessary → Fix the chemical anchor bolt → Remove the fork groove lifting device → Connect the cable → Finish the work. 2) Rack mounted installation process: Install fork groove lifting equipment → Clean the customer's installation surface, install positioning pins → Lower the robot vertically, tighten M20 bolts diagonally in stages → Remove lifting equipment → Connect wires.

The lifting fork slot must be removed before starting, otherwise serious equipment damage may occur.

Cable Wiring

The tightening torque of the grounding conductor M8 nut is 15 Nm;

KR   C4: Motor cable X20-X30, data cable X21-X31;

KR C5: motor cable XD30, data cable XF31; The tightening torque of the motor connector is 3 Nm; the data plug needs to be securely fastened with a snap lock;

After completing the wiring, it is necessary to verify the equipotential according to VDE0100 and EN60204-1; WorkVisual sets the actual installation posture (ground/wall mounted/ceiling).

Definition of Cable Pin

Provide complete pin allocation for KR C4 and KR C5 motor cables, data cables, and grounding cables;

A4 axis overtravel protection

A4 comes with an angle indicator and positioning pin. After losing the master point, it is necessary to determine the positive and negative directions based on which side of the angle mark the pin is on, and then perform a pre calibration notch operation.


Maintenance

The gearbox oil uniformly uses Optileb GT 1800/460 special oil, with filling capacities for each shaft: A1: 5.66   L; A2: 2.49   L; A3: 1.00   L; A4: 0.33   L; A5: 0.60   L; A6: 0.24   L.

Maintenance checklist

A1 cable kit inspection and lubrication: visually inspect the sheath, apply lubricating grease with a brush, and move A1 to evenly distribute the grease;

Oil change for each shaft gearbox: The gearbox should be at operating temperature to prevent burns; Ventilate and release pressure before draining oil; The tightening torque of M18/M10 magnetic plug is 20 Nm; the oil level is based on the lower edge of the inspection hole; Partial shaft oil change requires swinging to a specific posture (e.g. A4 requires A2+A3=-68 °); After changing the oil, conduct a T1 mode trial run to check for leaks.

Robot cleaning: Only solvent-free, water-soluble, chlorine free, non strong acid-base neutral cleaning agents are allowed, and steam spraying is prohibited.

Safety reminder: Once high-strength bolts (grade 10.9 or above) and stainless steel 70/80 bolts are loosened, they must be replaced with new parts and cannot be reused.


Maintenance (motor replacement, electrical system)

General steps for replacing A1/A2/A3 motors

A2 motor replacement must use a sling to fix the connecting rod arm; A3 motor replacement requires a sling to secure the built-in wrist and upper arm to prevent self weight from falling.

Unplug the motor and encoder right angle connectors; Remove the bolts; Remove the motor and protect the gear input shaft from dust.

New motor: Remove the rust proof protective layer; Apply Microlube GL261 lubricating grease thinly on the spline area; Check the O-ring; Install the motor without tilting it; Tighten the bolts diagonally multiple times; Insert the connector back to ensure that the anti rotation buckle is in place.

Restore the cover plate and remove the lifting device; The axis must be recalibrated for mastering; T1 mode test run.

Composition of Electrical System

A1-A3 cable assembly+micro RDC box; A4-A6 wrist cable; All motor power supply, brake, temperature, RDC encoder signal lines; X30/X31/PE external interface at the rear of the main body base. The document includes a complete set of wiring schematics: drawings for each axis motor, brake, temperature feedback, RDC encoder, and protective grounding circuit.


Retirement, storage, and disposal

Shutdown and disassembly process

The robot moves to the transport posture; Emergency stop and power outage; Remove the tool peripherals;

Disconnect the sealing gas (casting plate), cable, and grounding conductor; Loosen 8 M20 base bolts; Vertical lifting, pay attention to protecting the positioning pin to prevent the body from popping open and injuring people.

Storage Conditions

Store in a dry and dust-free place, reduce temperature fluctuations, avoid condensation, and direct sunlight; Storage temperature -40~60 ℃; After cleaning the robot, cover it properly and remove the tool attachments.

Scrap disposal

The disassembly of the body distinguishes between cast aluminum, copper, cast steel, steel, and electrical components, and is classified and recycled according to local regulations.


options: manual release device

Manually move the brake of each axis in power-off state: install and release tool kit; Remove the motor cover plate; Use the release tool to overcome the brake resistance and rotate the joint.

Important warning: After manually moving the shaft with power off, all shafts must be recalibrated to zero, otherwise it may cause collision and injury. Provide the installation steps for release tools, arrow label stickers, and torque parameters.

  • GE 369B1860G0026 MPU50 Nexus Controller
  • GE IS420ESWBH3A Industrial ESWB Ethernet Switch
  • GE IS420ESWBH2A Mark VIe IONet Network Switch
  • GE IS200SRTDH2ACB RTD Terminal Board Mark VI
  • GE SR469-P5-HI-A20 Motor Protection Relay
  • GE VMIVME-7750 Pentium III VME CPU Module
  • GE IS215UCVEH2AE VMIVME-7614-132 VME Controller Card
  • GE MVDL800-47931101-A Liquid-Cooled Delta Module for MV3000 Medium Voltage Drive Systems
  • ABB BRC410 SPBRC410 Harmony Bridge Controller
  • ABB PFCL201CE-50kN 3BSE006699D0005 Pressductor PillowBlock Load Cell
  • ABB 5SHY3545L0009 3BHB013085R0001 IGCT Module
  • Wika IPT10 - Process Pressure Transmitter
  • Omron SK20-C1DT-D - Programmable Controller PLC Unit
  • Foxboro Eckardt (Schneider) AE214 - Field Indicator Digital Display Meter
  • Omron CJ1W-OD232 - Transistor Output Unit PLC Module
  • Jetter JX2-IO16 - Digital Input Output Module PLC
  • SEFI ACS 48.6A-NS - Power Supply Unit
  • Schneider (Telemecanique) XBTF011110 - Magelis Membrane Keyboard Overlay
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Siemens 6SL3120-2TE13-0AA3 - Sinamics S120 Dual Motor Module Inverter
  • SEW Eurodrive MAS51A005-503-50 - Movidyn Servo Drive Controller
  • Record ATE 20 - Automatic Door Brake Motor
  • Record ATE STA 21 - Automatic Door Brake Motor
  • Sanyo Denki R2AA06040FXP02 - AC Servo Motor
  • Omron NX-ID4442 - DC Digital Input Unit PLC Module
  • Schneider (Telemecanique) XBTGT2330 - Magelis Advanced Touch Panel HMI
  • ABB DX561-A1 - AC500 Digital Input Output PLC Module
  • SEW Eurodrive MC07B0004-2A3-4-00 - Movitrac B AC Frequency Inverter Drive
  • Schneider (Telemecanique) FT20CBCL030 - Connection Communication Cable
  • Visions AXFR 600601 - Gap Control Side Board PCBA
  • Allen Bradley 1797-CEC-A-C01 - Flex Ex Communication Interface Adapter
  • Siemens 6ES5095-8MC03 - Simatic S5 Programmable Controller CPU
  • Tectrol / Pitney Bowes TC53S-1392 - Power Supply Unit
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Neste 0635-107 - Control Board for SLX Automatic Sliding Door
  • RSF Elektronik MS 2x.x4 MO - Linear Encoder Sensor
  • Pro-face GP37W2-BG41-24V - Graphic Terminal Operator Panel HMI
  • Allen Bradley 2711P-RP1 - PanelView Plus Logic Module HMI
  • ABB (Asea Brown Boveri) GNT0144700R0004 - Power Supply Electronic Board Module
  • SEW Eurodrive MC-LTE-B-0008-2B1-1-40 - Movitrac LTE AC Frequency Inverter Drive
  • Siemens 3RK1301-0AB10-0AA4 - Direct Starter Modular Motor Starter
  • Yaskawa SGDB-15VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9421 - 8-Channel C Series Digital Input Module
  • Yaskawa SGDB-10VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9476 - 32-Channel C Series Source Digital Output Module
  • Pitney Bowes R782000 - Turbojet Controller Board PCBA
  • Lika IT65-Y-1000BND2 - Incremental Encoder Sensor
  • Came 002ZT6 - Control Panel Board for Gear Motors
  • Desin HS-300/7500 - Multivariable Process Controller Unit
  • Pilz PNOZ mc1p - Modular Safety Relay Controller
  • Innovative Robotics PTNR2-2-NES - Controller Interface Board Module
  • Schneider Electric (Telemecanique) TSXCB4020 - Printer Communication Link Cable
  • Wika IPT10 - Process Pressure Transmitter
  • Schneider Electric (Modicon) TSXDMF342A - Extension Digital Analog Module for TSX17 PLC
  • Omron F150-KP - Vision System Cursor Key Pack Console
  • National Instruments BNC-2110 - Shielded Connector Block Accessory
  • Bosch Rexroth (Indramat) CSH01.2C-SE-EN2-EN2-CCD-NN-S-FW - Servo Drive Control Panel Interface Module
  • GHM / Gefran / Baumer GHM510573A/1000 - Incremental Encoder Sensor
  • National Instruments NI 9425 - 32-Channel C Series Digital Input Module
  • Schneider (Telemecanique) STBDDO3705 - Digital Output Module STB
  • Siemens 6EP1436-1SH01 - Regulated Power Supply Unit
  • Schneider Electric (Modicon) TSXFPP20 - Fipway PCMCIA Communication Board
  • April QMB 3202 - PLC Output Card Module with Parameter Surveillance
  • Siemens 6ES5240-1AA12 - Simatic S5 Communication Processor Module
  • Midi Engineering MI907A - Stepper Motor Midi Amplifier Driver
  • Schneider Electric (Telemecanique) TSXAEZ414 - TSX Series Analog Input Module
  • Schneider (Telemecanique) TSX17-20 - TSX17 Compact PLC Controller Unit
  • Siemens 6ES5955-3LC14 - Simatic S5 Modular Power Supply Unit
  • Schneider (Telemecanique) ATV66U72N4 - Altivar 66 AC Frequency Inverter Drive
  • Omron NX-OD4256 - Transistor Output Unit PLC Module
  • Yaskawa / Omron SGDH-04AE-OY - Sigma II Servo Drive 400W
  • RSF Elektronik MS 20.04-2M - Linear Encoder Scale Sensor
  • ITT GMW (Metrosx) DAA288-240 A - LED Message Display Board
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Sensorex Alpha-LSE - Display Inclinometer Indicator
  • Omron NX-DA3603 - Analog Output Unit PLC Module
  • Grundig Electronic NRP 02 - Power Supply Control Unit Module
  • ProSoft Technology RLX-FHES-F - RadioLinx Industrial Wireless Hotspot Router
  • Omron NX-EIC202 - EtherCAT Coupler Unit PLC Module
  • Omron NX-TS3201 - Temperature Sensor Input Unit PLC Module
  • Omron CQM1-CPU41-V1 - Sysmac CQM1 PLC CPU System
  • April CPU5001 - PLC CPU Processing Unit
  • Yaskawa JZDP-D008-020-E - Linear Servo Motor Actuator
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 2711-K3A17L - PanelView 300 Operator Terminal HMI
  • Schneider (Telemecanique) TSXAEM411 - TSX Series Analog Input Module
  • Schneider Electric (Telemecanique) XBTGT5330 - Magelis Advanced Touch Panel HMI
  • Siemens 6ES5928-3UA12 - Simatic S5 Central Processing Unit PLC
  • Schneider (Telemecanique) TSXSUP65 - Power Supply Module
  • Schneider (Telemecanique) TSXLES61 + TSXLES60 - TSX Series Fine Line Box Local Module
  • Siemens 6SE6440-2AD23-0BA1 - Micromaster 440 AC Frequency Inverter Drive
  • National Instruments NI 9205 - 32-Channel C Series Analog Input Module
  • Yaskawa CIMR-PCC42P2 - Varispeed AC Frequency Inverter Drive
  • ABB PM554-T-A1 - AC500 PLC CPU Module
  • National Instruments cDAQ-9178 - 8-Slot CompactDAQ USB Chassis Backplane
  • Allen Bradley 1786-RPA - ControlNet Repeater Adapter Module
  • Allen Bradley 1770-KFD - DH-485 Communication Interface Module
  • Grundig Electronic NSP 02 - Power Supply Control Unit Module
  • Teq Q07.K3S.002A - Control Panel Logic Board
  • Allen Bradley 1300-ITSSC - Signal Converter Interface Module
  • Omron CQM1H-CPU51 - CQM1H Modular PLC System
  • ProSoft Technology 4207-DFNT-MCM - ProLinx Industrial Gateway Module
  • Schneider Electric TSXSCP114 - RS485 PCMCIA Communication Board
  • Grundig NGE 01 - Power Supply Unit
  • Grundig NZP 03 - Power Supply Unit
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Danaher / Atlas Copco / Socapel SAM-PA-400-30-E - Servo Power Supply Controller Unit
  • Klöckner Moeller EM4-101-DD1 - Easy Control Relay Module
  • Bosch Rexroth DKC-10.3-012-3-MGP-01VRS - Indramat Digital Servo Controller Drive
  • Schneider (Telemecanique) XBTGT2110 - Magelis Touch Panel HMI with Cutter
  • Berger Lahr (Sig Positec) WD3-004.1802 - Stepper Motor Controller Driver
  • ProSoft Technology MVI56-WA-EIP - ControlLogix Wireless EtherNet/IP Communication Module
  • Allen Bradley 1794-ACNR15 - Flex I/O ControlNet Adapter Module
  • Fanuc A06B-6096-H201 - Servo Amplifier Module
  • Panasonic MSDA083A1 - AC Servo Driver Amplifier
  • Teq Q07.K3P.003B - Control Panel Logic Board
  • Schneider (Telemecanique) XBTH002010 - Magelis Operator Terminal HMI
  • Wika IPT10 - Process Pressure Transmitter
  • Teq Q07.A4P.001A - Control Panel I/O Module Board
  • Teq Q07.A3L.003A - Control Panel Module I/O Board
  • Siemens 6ES5246-4UA31 - Simatic S5 Positioning Module
  • Mitsubishi / Harmonic Drive HC-KFS43 - AC Servo Motor with Harmonic Reducer
  • Mitsubishi HC-KFS43 - AC Servo Motor
  • SES Store Electronic Systems 37120/120 - VLF Radio Transmitter Label System
  • Siemens 6SE9213-6BA40 - Micromaster AC Frequency Inverter Drive
  • Rosemount 1151DP5S22 - Differential Pressure Transmitter
  • Siemens 6FM1470-4AA20 - Simatic FM 470 Positioning Module Processor