K-WANG

+086-15305925923
Service expert in industrial control field!
NameDescriptionContent
Adequate Inventory, Timely Service
pursuit of excellence 
Ship control system
Equipment control system
Power monitoring system
Current position:
新闻动态
newS
   
Brand

Micro Innovation MICRO PANEL GS-2 Industrial Touch Visualization Operation Panel (HMI)

From: | Author:Wang | Time :2026-09-22 | 123 visit: | 🔊 Click to read aloud ❚❚ ▶ | Share:

Micro Innovation MICRO PANEL GS-2 Industrial Touch Visualization Operation Panel (HMI)

Product Overview

Core hardware components: GS-2 body+SMM system memory module (rear can be plugged and unplugged)+communication expansion board (slot type, such as MPB-TP multi protocol board).

Software: PDT software for PC, used to develop HMI project screens, downloaded to SMM module.

Important Disclaimer: This HMI cannot implement personnel or equipment protection safety functions; The manufacturer shall not be liable for any related losses caused by malfunction or damage; The document parameters are not legally guaranteed, and the technical specifications may be changed without notice.


Mechanical installation

2.1 Dimensions of external openings

Overall dimensions of the machine: 312  × 222  × 76   mm; weight approximately 3.5   kg

Cabinet opening: 296 × 194 mm; M5 fixed screw hole.

Display: 9-inch EL electroluminescent screen; The viewing angle is greater than 160 °.

2.2 Installation Requirements

Leave a minimum of 5cm of heat dissipation gap between the equipment and other components on the top, bottom, sides, and back; The heat dissipation and ventilation joints must not be obstructed by cables or objects.

Working conditions: Vertical installation, smooth air convection; Altitude ≤ 2000 meters.

IP65 front panel protection: Additional installation kit needs to be purchased (not included in the standard supply); The kit includes a rear compression frame to ensure that the sealing gasket is tightly pressed against the thin control cabinet panel in order to achieve IP65.


Interfaces, hardware buttons, and indicator lights

backplane interface 

Power supply terminal (3-pole plug-in terminal): 24VDC; PE protection ground, 0V.

Allowable voltage: 20.4~28.8   VDC; Ripple limit 18.5-30.2 VDC; Typical current consumption is 0.9A.

Two system power LEDs:+12V and+5V power status indicator lights.

ROG-PORT (9-pin D-Sub male, isolated RS232 programming port)

Purpose: PC download project; SMM-2 version can output logs through an external serial printer.

Pin 2=TxD, 3=RxD, 5=GND; 9-pin+5V (only allowed for use with original accessories, external third-party devices are prohibited from taking power); Shell shielding.

DOWNLOAD button: triggers the download system interface.

Slot: Pluggable communication board (MPB-TP, etc.).

Download cable

PC and PROG-PORT connection download project; Two D-Sub female heads, 2-6 pins connected 1:1 directly.

Only temporarily connect to the computer during debugging and downloading, the cable can be unshielded; When the equipment is running normally and the cable is retained, shielded copper braided cable must be used.


SMM system memory module

SMM is a tool free pluggable module at the back of the device, fixed with two rolling screws, storing operating system POS and Flash project engineering. SMM can only be disassembled and assembled in a power-off state, and touching the contacts with hands is prohibited to prevent ESD static damage.

Differences in Model, Specification, and Function

SMM-1 Standard Version Flash 128KB Basic HMI Screen Function

SMM-2 Enhanced Flash 512KB Multilingual; Larger image and text storage space; Support the recording of logs by the external serial port printer of PROG-PORT

SMM module comes with a WRITE-ENABLE write enable toggle switch

Normal operation: It must be turned off to disable writing and prevent accidental rewriting of the project.

Download project/rewrite project: Turn on to allow writing to Flash.

Be sure to switch back to OFF after downloading is complete.

Specification for Cable Manufacturing and EMC Shielding

To achieve the EMC index of the document, it is necessary to strictly follow the cable handling:

Communication board cable: must be a copper braided shielded cable with a metal shell D-Sub connector; The shielding layer is extensively crimped onto the metal shell of the joint, and it is prohibited to use only the terminal to crimp the shielding layer.

Cross control cabinet installation (HMI and PLC are different cabinets): Equipotential connection wires must be laid to avoid large compensation currents flowing through the shielding layer.

Printer cable (SMM-2): Copper braided shielding, metal joints at both ends grounded; The printer PE and HMI cabinet PE need to come from different power supply circuits.

Standard processing technology for shielding layer

Wire stripping; The shielding braided layer is shortened by about 3cm;

Fold the weaving layer outward and cover it with the outer sheath; Folding part of heat shrink tubing package; Retain 5-8mm exposed shielding;

Use a metal D-Sub connector with cable crimping clamps to firmly press the folded shielding layer and achieve low impedance shell grounding.


Built in system interface

6.1 Status (TROUBLE SHOOTING) fault diagnosis interface

The system automatically pops up, commonly caused by communication failure during startup of PLC or communication interruption during operation. Interface information:

POS operating system version, PDT engineering software version;

Memory partition status SYS/FONT/IMA/TXT;

Communication board status, PLC link status (OK/NOK), preset data status;

PROG-PORT (printer) status; Touch any position on the screen to exit the diagnostic interface and return to the project screen.

6.2 DOWNLOAD (PROJECT UP-DOWNLOAD) download interface

Press the DOWNLOAD button on the backboard to enter. Function: Project upload/download, set system clock; Display hardware version, memory capacity, and transfer block count.

Transfer Active flashes, indicating that it can receive PC downloads.

Start transmission with the START touch button; EXIT exit interface.


Complete steps for whole machine debugging and operation

Turn SMM module WRITE-ENABLE to OFF; Confirm that the hardware configuration of the communication board is correct.

Connect 24VDC power supply in power-off state, do not connect PLC communication cable for now.

Turn on the 24V power supply, run the system self-test, and load the built-in demo project.

A few seconds later, the TROUBLE SHOOTING fault diagnosis page pops up, and at this time, PLC LINK=NOK is considered normal (PLC not connected); Confirm that all Memories are OK; touch the screen to exit the diagnostic page.

Press the DOWNLOAD button to enter the download interface.

Set SMM's WRITE-ENABLE to ON (allow writing projects).

PC-GS2 connection download cable; Open the PDT software on the PC.

Press START on the HMI download interface; Transfer Active flashes, PC executes project download.

Download completed, HMI automatically restarts, self checks again.

Be sure to turn WRITE-ENABLE back to OFF!

Connect the PLC communication cable; HMI automatically establishes PLC communication; The PLC LINK status changes from NOK to OK.

Touch the screen to execute the preset, enter normal operation, and debugging is complete.


Communication board firmware upgrade Comboard Loader

Condition: HMI operating system POS version ≥ 5.01; The communication board supports Flash firmware.

Power off, unplug the communication board; Board jumper J7, switch from RUN to PRG programming mode; Insert the card back in.

Connect the ROG-PORT to the PC using a download cable; Run the COMLOAD. EXE loading tool on the PC.

Power on GS-2; The red light on the communication board is on, and the green light flashes 4 times per second before turning off. The HMI automatically enters the COMBOARD Loader upgrade interface.

PC issues firmware bin file; The flashing green light indicates normal packet reception;

Upgrade completed, power outage; Switch the board jumper back to RUN mode and reinstall the board; Upgrade completed.

The firmware version can be viewed on the DOWNLOAD system interface.


Compliance and Technical Parameters

CE EU compliance: meets EMC Directive 89/336/EWG, low voltage 73/23/EC;

Launch standard EN50081-2; Anti disturbance EN50082-2; Safety standard EN60950.

Display: 9-inch EL electroluminescence, 640 × 400; 70Hz refresh rate.

Operate infrared matrix touch, 39 × 25 touch channel.

Interface: The communication board supports TTY, current loop RS232、RS422、RS485; ROG-PORT isolates RS232, with a maximum baud rate of 9600 and a maximum cable length of 20 meters.

Environment: Storage -40~75 ℃; Anti vibration and impact meet the IEC68-2 series standards;

Protection: The front panel of the entire machine is IP65 (an additional installation kit is required).

  • GE 369B1860G0026 MPU50 Nexus Controller
  • GE IS420ESWBH3A Industrial ESWB Ethernet Switch
  • GE IS420ESWBH2A Mark VIe IONet Network Switch
  • GE IS200SRTDH2ACB RTD Terminal Board Mark VI
  • GE SR469-P5-HI-A20 Motor Protection Relay
  • GE VMIVME-7750 Pentium III VME CPU Module
  • GE IS215UCVEH2AE VMIVME-7614-132 VME Controller Card
  • GE MVDL800-47931101-A Liquid-Cooled Delta Module for MV3000 Medium Voltage Drive Systems
  • ABB BRC410 SPBRC410 Harmony Bridge Controller
  • ABB PFCL201CE-50kN 3BSE006699D0005 Pressductor PillowBlock Load Cell
  • ABB 5SHY3545L0009 3BHB013085R0001 IGCT Module
  • Wika IPT10 - Process Pressure Transmitter
  • Omron SK20-C1DT-D - Programmable Controller PLC Unit
  • Foxboro Eckardt (Schneider) AE214 - Field Indicator Digital Display Meter
  • Omron CJ1W-OD232 - Transistor Output Unit PLC Module
  • Jetter JX2-IO16 - Digital Input Output Module PLC
  • SEFI ACS 48.6A-NS - Power Supply Unit
  • Schneider (Telemecanique) XBTF011110 - Magelis Membrane Keyboard Overlay
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Siemens 6SL3120-2TE13-0AA3 - Sinamics S120 Dual Motor Module Inverter
  • SEW Eurodrive MAS51A005-503-50 - Movidyn Servo Drive Controller
  • Record ATE 20 - Automatic Door Brake Motor
  • Record ATE STA 21 - Automatic Door Brake Motor
  • Sanyo Denki R2AA06040FXP02 - AC Servo Motor
  • Omron NX-ID4442 - DC Digital Input Unit PLC Module
  • Schneider (Telemecanique) XBTGT2330 - Magelis Advanced Touch Panel HMI
  • ABB DX561-A1 - AC500 Digital Input Output PLC Module
  • SEW Eurodrive MC07B0004-2A3-4-00 - Movitrac B AC Frequency Inverter Drive
  • Schneider (Telemecanique) FT20CBCL030 - Connection Communication Cable
  • Visions AXFR 600601 - Gap Control Side Board PCBA
  • Allen Bradley 1797-CEC-A-C01 - Flex Ex Communication Interface Adapter
  • Siemens 6ES5095-8MC03 - Simatic S5 Programmable Controller CPU
  • Tectrol / Pitney Bowes TC53S-1392 - Power Supply Unit
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Neste 0635-107 - Control Board for SLX Automatic Sliding Door
  • RSF Elektronik MS 2x.x4 MO - Linear Encoder Sensor
  • Pro-face GP37W2-BG41-24V - Graphic Terminal Operator Panel HMI
  • Allen Bradley 2711P-RP1 - PanelView Plus Logic Module HMI
  • ABB (Asea Brown Boveri) GNT0144700R0004 - Power Supply Electronic Board Module
  • SEW Eurodrive MC-LTE-B-0008-2B1-1-40 - Movitrac LTE AC Frequency Inverter Drive
  • Siemens 3RK1301-0AB10-0AA4 - Direct Starter Modular Motor Starter
  • Yaskawa SGDB-15VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9421 - 8-Channel C Series Digital Input Module
  • Yaskawa SGDB-10VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9476 - 32-Channel C Series Source Digital Output Module
  • Pitney Bowes R782000 - Turbojet Controller Board PCBA
  • Lika IT65-Y-1000BND2 - Incremental Encoder Sensor
  • Came 002ZT6 - Control Panel Board for Gear Motors
  • Desin HS-300/7500 - Multivariable Process Controller Unit
  • Pilz PNOZ mc1p - Modular Safety Relay Controller
  • Innovative Robotics PTNR2-2-NES - Controller Interface Board Module
  • Schneider Electric (Telemecanique) TSXCB4020 - Printer Communication Link Cable
  • Wika IPT10 - Process Pressure Transmitter
  • Schneider Electric (Modicon) TSXDMF342A - Extension Digital Analog Module for TSX17 PLC
  • Omron F150-KP - Vision System Cursor Key Pack Console
  • National Instruments BNC-2110 - Shielded Connector Block Accessory
  • Bosch Rexroth (Indramat) CSH01.2C-SE-EN2-EN2-CCD-NN-S-FW - Servo Drive Control Panel Interface Module
  • GHM / Gefran / Baumer GHM510573A/1000 - Incremental Encoder Sensor
  • National Instruments NI 9425 - 32-Channel C Series Digital Input Module
  • Schneider (Telemecanique) STBDDO3705 - Digital Output Module STB
  • Siemens 6EP1436-1SH01 - Regulated Power Supply Unit
  • Schneider Electric (Modicon) TSXFPP20 - Fipway PCMCIA Communication Board
  • April QMB 3202 - PLC Output Card Module with Parameter Surveillance
  • Siemens 6ES5240-1AA12 - Simatic S5 Communication Processor Module
  • Midi Engineering MI907A - Stepper Motor Midi Amplifier Driver
  • Schneider Electric (Telemecanique) TSXAEZ414 - TSX Series Analog Input Module
  • Schneider (Telemecanique) TSX17-20 - TSX17 Compact PLC Controller Unit
  • Siemens 6ES5955-3LC14 - Simatic S5 Modular Power Supply Unit
  • Schneider (Telemecanique) ATV66U72N4 - Altivar 66 AC Frequency Inverter Drive
  • Omron NX-OD4256 - Transistor Output Unit PLC Module
  • Yaskawa / Omron SGDH-04AE-OY - Sigma II Servo Drive 400W
  • RSF Elektronik MS 20.04-2M - Linear Encoder Scale Sensor
  • ITT GMW (Metrosx) DAA288-240 A - LED Message Display Board
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Sensorex Alpha-LSE - Display Inclinometer Indicator
  • Omron NX-DA3603 - Analog Output Unit PLC Module
  • Grundig Electronic NRP 02 - Power Supply Control Unit Module
  • ProSoft Technology RLX-FHES-F - RadioLinx Industrial Wireless Hotspot Router
  • Omron NX-EIC202 - EtherCAT Coupler Unit PLC Module
  • Omron NX-TS3201 - Temperature Sensor Input Unit PLC Module
  • Omron CQM1-CPU41-V1 - Sysmac CQM1 PLC CPU System
  • April CPU5001 - PLC CPU Processing Unit
  • Yaskawa JZDP-D008-020-E - Linear Servo Motor Actuator
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 2711-K3A17L - PanelView 300 Operator Terminal HMI
  • Schneider (Telemecanique) TSXAEM411 - TSX Series Analog Input Module
  • Schneider Electric (Telemecanique) XBTGT5330 - Magelis Advanced Touch Panel HMI
  • Siemens 6ES5928-3UA12 - Simatic S5 Central Processing Unit PLC
  • Schneider (Telemecanique) TSXSUP65 - Power Supply Module
  • Schneider (Telemecanique) TSXLES61 + TSXLES60 - TSX Series Fine Line Box Local Module
  • Siemens 6SE6440-2AD23-0BA1 - Micromaster 440 AC Frequency Inverter Drive
  • National Instruments NI 9205 - 32-Channel C Series Analog Input Module
  • Yaskawa CIMR-PCC42P2 - Varispeed AC Frequency Inverter Drive
  • ABB PM554-T-A1 - AC500 PLC CPU Module
  • National Instruments cDAQ-9178 - 8-Slot CompactDAQ USB Chassis Backplane
  • Allen Bradley 1786-RPA - ControlNet Repeater Adapter Module
  • Allen Bradley 1770-KFD - DH-485 Communication Interface Module
  • Grundig Electronic NSP 02 - Power Supply Control Unit Module
  • Teq Q07.K3S.002A - Control Panel Logic Board
  • Allen Bradley 1300-ITSSC - Signal Converter Interface Module
  • Omron CQM1H-CPU51 - CQM1H Modular PLC System
  • ProSoft Technology 4207-DFNT-MCM - ProLinx Industrial Gateway Module
  • Schneider Electric TSXSCP114 - RS485 PCMCIA Communication Board
  • Grundig NGE 01 - Power Supply Unit
  • Grundig NZP 03 - Power Supply Unit
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Danaher / Atlas Copco / Socapel SAM-PA-400-30-E - Servo Power Supply Controller Unit
  • Klöckner Moeller EM4-101-DD1 - Easy Control Relay Module
  • Bosch Rexroth DKC-10.3-012-3-MGP-01VRS - Indramat Digital Servo Controller Drive
  • Schneider (Telemecanique) XBTGT2110 - Magelis Touch Panel HMI with Cutter
  • Berger Lahr (Sig Positec) WD3-004.1802 - Stepper Motor Controller Driver
  • ProSoft Technology MVI56-WA-EIP - ControlLogix Wireless EtherNet/IP Communication Module
  • Allen Bradley 1794-ACNR15 - Flex I/O ControlNet Adapter Module
  • Fanuc A06B-6096-H201 - Servo Amplifier Module
  • Panasonic MSDA083A1 - AC Servo Driver Amplifier
  • Teq Q07.K3P.003B - Control Panel Logic Board
  • Schneider (Telemecanique) XBTH002010 - Magelis Operator Terminal HMI
  • Wika IPT10 - Process Pressure Transmitter
  • Teq Q07.A4P.001A - Control Panel I/O Module Board
  • Teq Q07.A3L.003A - Control Panel Module I/O Board
  • Siemens 6ES5246-4UA31 - Simatic S5 Positioning Module
  • Mitsubishi / Harmonic Drive HC-KFS43 - AC Servo Motor with Harmonic Reducer
  • Mitsubishi HC-KFS43 - AC Servo Motor
  • SES Store Electronic Systems 37120/120 - VLF Radio Transmitter Label System
  • Siemens 6SE9213-6BA40 - Micromaster AC Frequency Inverter Drive
  • Rosemount 1151DP5S22 - Differential Pressure Transmitter
  • Siemens 6FM1470-4AA20 - Simatic FM 470 Positioning Module Processor