Mitsubishi Electric GOT2000 Series GT23 Touchscreen (HMI) General Instructions

Mitsubishi Electric GOT2000 Series GT23 Touchscreen (HMI) General Instructions

Mitsubishi Electric GOT2000 Series GT23 Touchscreen (HMI) General Manual (IB0800503ENG-K), covering GT2310-VTBA / GT2308-VTBA / GT2310-VTBD / GT2308-VTBD  The complete explanation of safety precautions, hardware specifications, interface definitions, installation wiring, EMC compliance, maintenance, scrapping and other necessary engineering information for the four models is the core basis for on-site installation, commissioning and maintenance of GT23.

Core safety precautions (mandatory)

1. Design Warning

Touch screen malfunction may result in output holding/abnormal action, and an external safety circuit must be installed.

It cannot be used as the only device for emergency shutdown/major alarm and requires independent hardware redundancy.

Backlight failure can cause touch failure, and the status needs to be determined through POWER LED.

Do not touch multiple points simultaneously (simulating a resistive screen) to avoid misoperation.

2. Install Warning

Disassembly/wiring must be completely powered off to prevent electric shock, damage, and misoperation.

Grounding resistance ≤ 100 Ω, FG/LG must be reliably grounded.

Strictly follow the tightening torque of screws:

Installation screw: 0.36-0.48 N · m

Power terminal: 0.5-0.8 N · m

3. Use CAUTION

Separate the communication line from the power line by ≥ 100mm to avoid interference.

Do not touch the screen with sharp objects.

Inserting or unplugging SD/USB requires waiting for the access light to turn off.

The battery is non rechargeable, disassembled, heated, short circuited, and put into fire.

Core features of the product

Rich standard interfaces

Support multiple FA device connections

SD/SDHC card high-speed storage

Dual USB (Host+Device)

Improved usability

Complete fault diagnosis

Simple screen production

PC like operating experience

Highly compatible with Mitsubishi FA equipment

Easy to replace

LED backlight

Component names and interfaces (overall layout)

Display screen+analog resistive touch panel

POWER LED

Blue: Normal power supply

Orange: screensaver

Orange/blue flashing: backlight malfunction

Extinguish: No electricity

SD card interface+access LED+security cover

USB Host (Type-A): connected to mouse/keyboard/barcode scanner

USB Device (Mini-B): Download project from PC

Ethernet RJ45

RS-232 (9-pin male)

RS-422/485 (9-pin female head)

Terminal resistance switch (422/485)

battery compartment

Power terminals (L/N/DC+DC -/FG/LG)

Technical specifications (key)

1. General specifications

Working temperature: 0-55 ℃ (horizontal installation ≤ 40 ℃)

Storage temperature: -20~60 ℃

Humidity: 10-90% RH, no condensation

Altitude: ≤ 2000m

Protection: Installed inside the panel, pollution level 2, overvoltage category II

Grounding: ≤ 100 Ω, wire diameter ≥ 2mm ²

Cooling: Self cooling

2. Power specifications

AC powered type (VTBA)

Voltage: 100-240V AC

Power consumption: GT2310 ≤ 18W, GT2308 ≤ 11W

Allow instantaneous power outage: ≤ 20ms

Voltage resistance: 1500V AC for 1 minute

DC powered type (VTBD)

Voltage: 24V DC (+25/-20%)

Power consumption: GT2310 ≤ 16W, GT2308 ≤ 11W

Allow instantaneous power outage: ≤ 10ms

Voltage resistance: 350V AC for 1 minute

3. Touch panel

Type: Analog Resistance

Attention: Multi touch is not supported, and long-term use requires calibration for offset

Installation specifications

Panel opening size

GT2310：289×200mm（+2/0）

GT2308：227×176mm（+2/0）

Panel thickness: 1.6-4mm

Installation gap

Reserve sufficient space up, down, left, right for heat dissipation and wiring

Bottom reserved ≥ 100mm (open cover maintenance)

installation angle

60-105 ° C: Temperature ≤ 55 ℃

Other angles: Temperature ≤ 40 ℃

EMC&Low Voltage Directive (European Compliance)

EMC requirements

Launch: CISPR 16

Anti disturbance: static 4kV/8kV, radiation field 10V/m, surge, pulse group, etc

Key measures

Must be installed inside the conductive control cabinet

Cabinet door high-frequency low impedance grounding

LG/FG short circuited and grounded nearby (≤ 30cm)

Separate wiring of power lines and communication lines

Recommended noise filter

Schaffner FN343-3/05、FN660-6/06

TDK RSHN-2003

China RoHS Hazardous Substance List

Circuit board components and metal parts contain lead (Pb), and other harmful substances are within the limits.

The identification is applicable to the Chinese market.

Packaging List

GT23 host x 1

Install pendant x 4

General instruction manual (in Chinese and English) x 1

Maintenance and scrapping

maintain

Power off, clean, and tighten terminal screws

Anti static operation

Battery processing

Use Mitsubishi designated batteries

Classify and recycle according to local regulations

scrap

Treat as industrial waste

Separate recycling of batteries