K-WANG

+086-15305925923
Service expert in industrial control field!
NameDescriptionContent
Adequate Inventory, Timely Service
pursuit of excellence 
Ship control system
Equipment control system
Power monitoring system
Current position:
新闻动态
newS
   
Brand

GE Series 90–70 Genius Bus Controller

From: | Author:Wang | Time :2025-08-19 | 559 visit: | 🔊 Click to read aloud ❚❚ ▶ | Share:


GE Series 90–70 Genius Bus Controller 

Product Overview

Series 90-70 Genius Bus Controller (model IC697BEM731) is an interface module used to connect Genius I/O serial bus with Series 90-70 PLC. It supports communication with Genius I/O blocks, remote I/O sites, handheld monitors, and other devices, and can achieve functions such as data transmission, diagnosis, distributed control, and redundancy. It follows multiple international standards and is suitable for various automation control scenarios.


Warning and Precautions Explanation

Warning: Used to emphasize the presence of hazardous voltage, current, temperature, or other conditions in the equipment that may cause personal injury, and is intended for use in situations where negligence may result in personal injury or equipment damage.

Caution: Used to indicate situations where equipment may be damaged if not careful.

Note: Used only to remind users of particularly important information that is helpful for understanding and operating the device.

System Overview

The Series 90-70 PLC bus controller (product number IC697BEM731) is used to connect the Genius I/O serial bus to the Series 90-70 PLC.

The devices that Genius bus can serve include:

Genius module: Provides interfaces with various discrete, analog, and special-purpose field devices, with advanced diagnostic capabilities and many software configurable features.

Remote nodes: Series 90-70 I/O racks connected to the bus through remote I/O scanner modules, each remote node can contain any combination of discrete and analog I/O modules, providing up to 128 bytes of input data and 128 bytes of output data.

Handheld monitor: can be used as a portable device or permanently installed, providing a convenient operator interface for module settings, data monitoring, and diagnostics.

Multiple hosts: used for communication through datagrams and global data.

Bus can achieve various functions, such as enhancing I/O control through communication commands in the program, only used for I/O control, dedicated for CPU communication, and can also develop more complex systems.


Number of bus controllers

Series 90-70 PLC systems with CPU versions 3.0 and higher can contain up to 31 bus controllers.

Early CPU versions could accommodate up to 16 bus controllers.

In some redundant system configurations, there are fewer available bus controllers, as detailed in Chapter 6.

I/O devices on the bus

The I/O devices on the bus can be Genius I/O modules or standard Series 90-70 I/O modules in one or more remote nodes.

The total number of I/O circuits that a Genius bus can serve depends on the type of I/O device used and the available memory in the CPU.

Memory requirements for Genius module:

For% I and% Q memory, the size shown is in bits; For% AI and% AQ memory, the size shown is in words.

Different types of modules (such as 115 VAC grouped I/O modules, 115 VAC isolated I/O modules, etc.) have different maximum memory requirements.

Many Genius I/O modules have both inputs and outputs on the same module. Modules configured as both inputs and outputs in Logicmaster 90 software will occupy the same reference in% I and% Q memory. Unused references cannot be allocated to other inputs or outputs and should not be used in applications.

Memory requirements for remote nodes: A 90-70 remote I/O scanner (IC697BEM733) and the modules it serves form a remote node on the Genius bus. The remote node can include any combination of Series 90-70 discrete and analog input-output modules, with a maximum total of 128 bytes of input and 128 bytes of output (8 discrete points represent one byte, and 1 analog channel uses 2 bytes).


Bus controller description

The bus controller is a standard rack mounted Series 90-70 PLC module.

Status LED: The front LED indicates its operating status, the top two LEDs should light up during normal operation, and the bottom LED is not in use.

Module OK: Displays the status of the bus controller and flashes during power on diagnostics.

Channel OK: Displays the status of the bus. It lights up steadily when the bus is running normally, flashes intermittently when there are bus errors, goes off when the bus is faulty, and also goes off when no configuration is received from the PLC CPU.

Handheld monitor connector: The handheld monitor connector on the bus controller panel is used to connect a handheld monitor. For the IC697BEM931 bus controller, if there is a lower HHM connector, it is not used. Except for the allocation of I/O module device numbers, all handheld monitor functions can be executed through HHM connected to the bus controller. It is recommended to use IC660HHM501C (or higher version) handheld monitor to ensure normal operation with Series 90-70 PLC.

Terminal components: The serial bus and shielded wire are connected to the removable terminal block on the front of the bus controller. For the IC697BEM931 bus controller, only the upper three terminals are used. To remove terminal components without interfering with bus continuity, jumper wires are required, as detailed in Chapter 2.

Genius bus

Bus type: Daisy chained bus cable; Single twisted pair cable with shielding or Twinax. Fiber optic cables and modems can also be used.

Bus terminal: Connect 75, 100, 120, or 150 ohm resistors at both ends of the electrical bus cable.

Baud rate: configurable, standard 153.6 Kbaud, extended 153.6 Kbaud, 76.8 Kbaud, or 38.4 Kbaud.

Maximum bus length: 7500 feet at 38.4 Kbaud, 4500 feet at 76.8 Kbaud, 3500 feet at 153.6 Kbaud expansion, and 2000 feet at standard 153.6 Kbaud. The maximum length at each baud rate also depends on the cable type. Chapter 2 provides a complete list of cable types, displaying the corresponding bus length and baud rate. Using fiber optic cable segments with modems can achieve longer bus lengths.

Maximum number of devices: 32 devices at 153.6 Kbaud standard, 153.6 Kbaud extension, or 76.8 Kbaud; At 38.4 Kbaud, there are 16 devices, including a bus controller, and usually one handheld monitor.

Data encoding: Each bit is encoded as three double pulses, and the receiver performs a majority vote to correct any single double pulse error. Double pulse is an AC code consisting of a positive voltage followed by a negative voltage offset, which is sampled separately to suppress low-frequency and high-frequency interference.

Modulation technique: Frequency Shift Keying (FSK) 0 to 460.8 KHz maximum (153.6 Kilobaud).

Isolation: 2000V high voltage, 1500V transient common mode suppression.

Signal to noise ratio: 60 dB.

Bus controller operation

The bus controller handles all data transfers between the PLC and devices on the bus, requiring the docking of two completely independent and asynchronous activities: Genius bus scanning (the communication cycle between devices on the bus, following the order of bus addresses 0-31) and CPU scanning (including the operation cycle of communication between the CPU and the bus controller).

The bus controller manages data transfer between the bus and CPU by maintaining two independent onboard RAM memories, one with the bus interface and the other with the CPU interface. The bus controller automatically transfers data between these two memories and provides data to the bus or CPU when needed.

Genius bus scan: Bus scan includes a complete cycle of "tokens" between devices on the bus, which may include other bus controllers or remote I/O scanners, as well as Genius modules. During bus scanning, the bus controller automatically performs operations such as receiving all input data sent by devices on the bus, broadcasting global data, updating outputs (if allowed), receiving any fault messages sent by devices on the bus and setting diagnostic status references for CPU use, and sending individual commands received from the CPU to the corresponding devices. The time required for communication tokens to be transmitted to all devices depends on the baud rate, the number and type of devices on the bus, and the usage of global data and datagram communication.

Input data from devices on the bus: Every time a module or remote I/O scanner has a communication token, the bus controller receives the input data they send (as this data is broadcast, it may be received by any other bus interface module running on the bus). The bus controller stores all received input data, and the CPU reads all discrete and analog inputs from the bus controller every time it scans (analog data is not multiplexed).

Output data from CPU: As the application program executes, the CPU sends output and any commands to the bus controller, which stores this data and transmits it on the bus every time it has a communication token. Unlike the input of broadcasting, the output is directed to the specific device that should receive them.

Diagnosis: Genius modules and other devices on the bus will automatically report faults, alarms, and certain other predefined conditions to the PLC. During any bus scan, only one diagnostic message can be sent. If a fault message has already been sent (by another device) during that scan, the device will save its diagnostic message to the next available bus scan. The bus controller stores any diagnostic messages received, and the Series 90-70 CPU automatically reads them. The Logicmaster 90-70 software can then be used to display the fault in the fault table and clear it from the programmer. For details, see Chapter 4. Genius handheld monitors can also be used for diagnosis and troubleshooting. In addition to the built-in diagnostic capabilities of Genius devices, the Logicmaster 90-70 application can also utilize other diagnostic mechanisms provided by the Series 90-70 PLC, such as system state references defined for Genius, fault and fault free contacts that can be used to detect faults and no fault conditions, and alarm contacts that can be used to indicate when simulated values reach specified alarm limits.

Datagrams

The Series 90-70 bus controller supports all Genius datagrams, including Read ID、Read ID Reply、Read Configuration、Read Configuration Reply、Write Configuration、Assign Monitor、Read Diagnostics、Read Diagnostics Reply、Write Point、Read Block I/O、Read Block I/O Reply、Report Fault、Pulse Test、Pulse Test Complete、Clear Circuit Fault、Clear All Circuit Faults、Switch BSM、Read Device、Read Device Reply、Write Device、Read Data、Read Data Reply、Write Data、Read Map、Read Map Reply、Write Map  Wait, each type of datagram has its specific description and function.

  • GE 369B1860G0026 MPU50 Nexus Controller
  • GE IS420ESWBH3A Industrial ESWB Ethernet Switch
  • GE IS420ESWBH2A Mark VIe IONet Network Switch
  • GE IS200SRTDH2ACB RTD Terminal Board Mark VI
  • GE SR469-P5-HI-A20 Motor Protection Relay
  • GE VMIVME-7750 Pentium III VME CPU Module
  • GE IS215UCVEH2AE VMIVME-7614-132 VME Controller Card
  • GE MVDL800-47931101-A Liquid-Cooled Delta Module for MV3000 Medium Voltage Drive Systems
  • ABB BRC410 SPBRC410 Harmony Bridge Controller
  • ABB PFCL201CE-50kN 3BSE006699D0005 Pressductor PillowBlock Load Cell
  • ABB 5SHY3545L0009 3BHB013085R0001 IGCT Module
  • Wika IPT10 - Process Pressure Transmitter
  • Omron SK20-C1DT-D - Programmable Controller PLC Unit
  • Foxboro Eckardt (Schneider) AE214 - Field Indicator Digital Display Meter
  • Omron CJ1W-OD232 - Transistor Output Unit PLC Module
  • Jetter JX2-IO16 - Digital Input Output Module PLC
  • SEFI ACS 48.6A-NS - Power Supply Unit
  • Schneider (Telemecanique) XBTF011110 - Magelis Membrane Keyboard Overlay
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Siemens 6SL3120-2TE13-0AA3 - Sinamics S120 Dual Motor Module Inverter
  • SEW Eurodrive MAS51A005-503-50 - Movidyn Servo Drive Controller
  • Record ATE 20 - Automatic Door Brake Motor
  • Record ATE STA 21 - Automatic Door Brake Motor
  • Sanyo Denki R2AA06040FXP02 - AC Servo Motor
  • Omron NX-ID4442 - DC Digital Input Unit PLC Module
  • Schneider (Telemecanique) XBTGT2330 - Magelis Advanced Touch Panel HMI
  • ABB DX561-A1 - AC500 Digital Input Output PLC Module
  • SEW Eurodrive MC07B0004-2A3-4-00 - Movitrac B AC Frequency Inverter Drive
  • Schneider (Telemecanique) FT20CBCL030 - Connection Communication Cable
  • Visions AXFR 600601 - Gap Control Side Board PCBA
  • Allen Bradley 1797-CEC-A-C01 - Flex Ex Communication Interface Adapter
  • Siemens 6ES5095-8MC03 - Simatic S5 Programmable Controller CPU
  • Tectrol / Pitney Bowes TC53S-1392 - Power Supply Unit
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Neste 0635-107 - Control Board for SLX Automatic Sliding Door
  • RSF Elektronik MS 2x.x4 MO - Linear Encoder Sensor
  • Pro-face GP37W2-BG41-24V - Graphic Terminal Operator Panel HMI
  • Allen Bradley 2711P-RP1 - PanelView Plus Logic Module HMI
  • ABB (Asea Brown Boveri) GNT0144700R0004 - Power Supply Electronic Board Module
  • SEW Eurodrive MC-LTE-B-0008-2B1-1-40 - Movitrac LTE AC Frequency Inverter Drive
  • Siemens 3RK1301-0AB10-0AA4 - Direct Starter Modular Motor Starter
  • Yaskawa SGDB-15VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9421 - 8-Channel C Series Digital Input Module
  • Yaskawa SGDB-10VD - Servopack Servo Drive Amplifier
  • National Instruments NI 9476 - 32-Channel C Series Source Digital Output Module
  • Pitney Bowes R782000 - Turbojet Controller Board PCBA
  • Lika IT65-Y-1000BND2 - Incremental Encoder Sensor
  • Came 002ZT6 - Control Panel Board for Gear Motors
  • Desin HS-300/7500 - Multivariable Process Controller Unit
  • Pilz PNOZ mc1p - Modular Safety Relay Controller
  • Innovative Robotics PTNR2-2-NES - Controller Interface Board Module
  • Schneider Electric (Telemecanique) TSXCB4020 - Printer Communication Link Cable
  • Wika IPT10 - Process Pressure Transmitter
  • Schneider Electric (Modicon) TSXDMF342A - Extension Digital Analog Module for TSX17 PLC
  • Omron F150-KP - Vision System Cursor Key Pack Console
  • National Instruments BNC-2110 - Shielded Connector Block Accessory
  • Bosch Rexroth (Indramat) CSH01.2C-SE-EN2-EN2-CCD-NN-S-FW - Servo Drive Control Panel Interface Module
  • GHM / Gefran / Baumer GHM510573A/1000 - Incremental Encoder Sensor
  • National Instruments NI 9425 - 32-Channel C Series Digital Input Module
  • Schneider (Telemecanique) STBDDO3705 - Digital Output Module STB
  • Siemens 6EP1436-1SH01 - Regulated Power Supply Unit
  • Schneider Electric (Modicon) TSXFPP20 - Fipway PCMCIA Communication Board
  • April QMB 3202 - PLC Output Card Module with Parameter Surveillance
  • Siemens 6ES5240-1AA12 - Simatic S5 Communication Processor Module
  • Midi Engineering MI907A - Stepper Motor Midi Amplifier Driver
  • Schneider Electric (Telemecanique) TSXAEZ414 - TSX Series Analog Input Module
  • Schneider (Telemecanique) TSX17-20 - TSX17 Compact PLC Controller Unit
  • Siemens 6ES5955-3LC14 - Simatic S5 Modular Power Supply Unit
  • Schneider (Telemecanique) ATV66U72N4 - Altivar 66 AC Frequency Inverter Drive
  • Omron NX-OD4256 - Transistor Output Unit PLC Module
  • Yaskawa / Omron SGDH-04AE-OY - Sigma II Servo Drive 400W
  • RSF Elektronik MS 20.04-2M - Linear Encoder Scale Sensor
  • ITT GMW (Metrosx) DAA288-240 A - LED Message Display Board
  • Allen Bradley 1757-SRM - ControlLogix Redundancy Module
  • Sensorex Alpha-LSE - Display Inclinometer Indicator
  • Omron NX-DA3603 - Analog Output Unit PLC Module
  • Grundig Electronic NRP 02 - Power Supply Control Unit Module
  • ProSoft Technology RLX-FHES-F - RadioLinx Industrial Wireless Hotspot Router
  • Omron NX-EIC202 - EtherCAT Coupler Unit PLC Module
  • Omron NX-TS3201 - Temperature Sensor Input Unit PLC Module
  • Omron CQM1-CPU41-V1 - Sysmac CQM1 PLC CPU System
  • April CPU5001 - PLC CPU Processing Unit
  • Yaskawa JZDP-D008-020-E - Linear Servo Motor Actuator
  • Bronkhorst P-702C-FAC-88-Z - Digital Mass Flow Controller
  • Allen Bradley 2711-K3A17L - PanelView 300 Operator Terminal HMI
  • Schneider (Telemecanique) TSXAEM411 - TSX Series Analog Input Module
  • Schneider Electric (Telemecanique) XBTGT5330 - Magelis Advanced Touch Panel HMI
  • Siemens 6ES5928-3UA12 - Simatic S5 Central Processing Unit PLC
  • Schneider (Telemecanique) TSXSUP65 - Power Supply Module
  • Schneider (Telemecanique) TSXLES61 + TSXLES60 - TSX Series Fine Line Box Local Module
  • Siemens 6SE6440-2AD23-0BA1 - Micromaster 440 AC Frequency Inverter Drive
  • National Instruments NI 9205 - 32-Channel C Series Analog Input Module
  • Yaskawa CIMR-PCC42P2 - Varispeed AC Frequency Inverter Drive
  • ABB PM554-T-A1 - AC500 PLC CPU Module
  • National Instruments cDAQ-9178 - 8-Slot CompactDAQ USB Chassis Backplane
  • Allen Bradley 1786-RPA - ControlNet Repeater Adapter Module
  • Allen Bradley 1770-KFD - DH-485 Communication Interface Module
  • Grundig Electronic NSP 02 - Power Supply Control Unit Module
  • Teq Q07.K3S.002A - Control Panel Logic Board
  • Allen Bradley 1300-ITSSC - Signal Converter Interface Module
  • Omron CQM1H-CPU51 - CQM1H Modular PLC System
  • ProSoft Technology 4207-DFNT-MCM - ProLinx Industrial Gateway Module
  • Schneider Electric TSXSCP114 - RS485 PCMCIA Communication Board
  • Grundig NGE 01 - Power Supply Unit
  • Grundig NZP 03 - Power Supply Unit
  • Siemens 6ES5246-4UA41 - Simatic S5 Positioning Module
  • Danaher / Atlas Copco / Socapel SAM-PA-400-30-E - Servo Power Supply Controller Unit
  • Klöckner Moeller EM4-101-DD1 - Easy Control Relay Module
  • Bosch Rexroth DKC-10.3-012-3-MGP-01VRS - Indramat Digital Servo Controller Drive
  • Schneider (Telemecanique) XBTGT2110 - Magelis Touch Panel HMI with Cutter
  • Berger Lahr (Sig Positec) WD3-004.1802 - Stepper Motor Controller Driver
  • ProSoft Technology MVI56-WA-EIP - ControlLogix Wireless EtherNet/IP Communication Module
  • Allen Bradley 1794-ACNR15 - Flex I/O ControlNet Adapter Module
  • Fanuc A06B-6096-H201 - Servo Amplifier Module
  • Panasonic MSDA083A1 - AC Servo Driver Amplifier
  • Teq Q07.K3P.003B - Control Panel Logic Board
  • Schneider (Telemecanique) XBTH002010 - Magelis Operator Terminal HMI
  • Wika IPT10 - Process Pressure Transmitter
  • Teq Q07.A4P.001A - Control Panel I/O Module Board
  • Teq Q07.A3L.003A - Control Panel Module I/O Board
  • Siemens 6ES5246-4UA31 - Simatic S5 Positioning Module
  • Mitsubishi / Harmonic Drive HC-KFS43 - AC Servo Motor with Harmonic Reducer
  • Mitsubishi HC-KFS43 - AC Servo Motor
  • SES Store Electronic Systems 37120/120 - VLF Radio Transmitter Label System
  • Siemens 6SE9213-6BA40 - Micromaster AC Frequency Inverter Drive
  • Rosemount 1151DP5S22 - Differential Pressure Transmitter
  • Siemens 6FM1470-4AA20 - Simatic FM 470 Positioning Module Processor