K-WANG

+086-15305925923

Service expert in industrial control field！

English 简体中文

NameDescriptionContent

Adequate Inventory, Timely Service

pursuit of excellence

Ship control system

Equipment control system

Power monitoring system

Current position:

Home >> GE >> GE VMIPMC-5565 Ultrahigh Speed Fiber-Optic Reflective Memory with Interrupts

新闻动态

newS

Brand

GE VMIPMC-5565 Ultrahigh Speed Fiber-Optic Reflective Memory with Interrupts

The V7768/V7769 conform to the VME physical specification for a 6U board. The

V7768/V7769 can be used for the system controller or as a peripheral board. It can

be plugged directly into any standard chassis accepting either type of board.

The following steps describe the GE-recommended method for installation and

powerup of the V7768/V7769:

1. If a PMC module is to be used, connect it to the V7768/V7769 prior to board

installation (as shown in Figure 1-4 on page 28). Refer to the Product Manual for the PMC module for configuration and setup.

NOTE

Air flow as measured at the output side of the heatsink is to be

greater than 450 LFM.

2. Insert the V7768/V7769 into a VME chassis system controller or peripheral

slot. While ensuring that the board is properly aligned and oriented in the

supporting board guides, slide the board smoothly forward against the mating connector. Use the ejector handles to firmly seat the board.

3. All needed peripherals can be accessed from the front panel or the rear I/O.

Each connector is clearly labeled, and detailed pinouts are in Appendix A:

Connector Pinouts.

4. Connect a keyboard and mouse if the system has not been previously configured.

5. The V7768 features an optional CompactFlash Disk resident on the board.

Refer to Chapter 3: Embedded PC/RTOS Features for setup details.

6. If an external drive module is installed, the BIOS Setup program must be

used to configure the drive types. See Appendix B: AMI BIOS Setup Utility

to properly configure the system.

7. If a drive module is present, install the operating system according to the

manufacturer’s instructions.

1.3.1 BIOS Setup

The V7768/V7769 has an onboard BIOS Setup program that controls many

configuration options. These options are saved in a special non-volatile, batterybacked memory chip and are collectively referred to as the board’s CMOS

Configuration. The CMOS configuration controls many details concerning the

behavior of the hardware from the moment power is applied.

Details of the V7768/V7769 BIOS setup program are included in

Appendix B: AMI BIOS Setup Utility

The V7768/V7769 provide front panel access for the PMC expansion site, an

optional Gigabit Ethernet port, one 10/100 RJ45 connector, one serial port, SVGA,

keyboard/mouse, the manual reset switch and the status LEDs. A drawing of the

V7768/V7769 front panels are shown in Figure 1-7 and Figure 1-8. The front panel

connectors and indicators are labeled as follows:

V7768 • USB Dual USB 2.0 Ports

• LAN1 10/100/1000 Mbit Ethernet connector for port 1

• LAN2 10/100/1000 Mbit Ethernet connector for port 2

• M/K Mouse/keyboard connector

• COM1 Serial Port

• RST Manual reset switch

• BPHT Status LEDs

• VGA Analog Video connector

• A L Activity and Link Status LEDs for rear GbE

V7769 • SATA Serial ATA Activity LED

• SAS1 SAS Lane 1

• SAS2 SAS Lane 2

• HB Heartbeat LED for SAS/SATA controller

The V7768/V7769 provide rear I/O support for the following: digital video, two

SATA ports, one Serial and four USB ports. The V7768/V7769 are compatible with

GE’s Rear Transition Modules ACC-0602RC and

ACC-0603RC.

The front panel connectors, including connector pinouts and orientation, for the

V7768/V7769 are defined in Appendix A: Connector Pinouts.

上一篇： GE VMIVME-......

下一篇： GE VMIVME-......

ABB 3BHE039724R2643 PPD513 AC 800PEC High-Speed Controller for Power Electronic and Excitation Control Systems
SHINKAWA FRP 360A - BOARD
SHINKAWA IBP-43AM - PCB Board
SHINKAWA IBP-42-M - PCB Board
SHINKAWA DSP-11C - PCB Board
SHINKAWA FRP-341E - BOARD
SHINKAWA CPP-111 - PCB Board
SHINKAWA FRP-342A - BOARD
SHINKAWA FRP-341D - BOARD
SHINKAWA MDP-X MDP-135 - PCB Board
SHINKAWA MGP-57 - BOARD
SHINKAWA FRP-226A - PCB Board
SHINKAWA MDP-141 - PCB Board
SHINKAWA IOP-188 - BOARD
SHINKAWA FRP-341C - BOARD
SHINKAWA MDP-90 - PCB Board
SHINKAWA CPP-107A - PCB Board
SHINKAWA FRP-227A - PCB Board
SHINKAWA FRP-249A - PCB Board
SHINKAWA MDP-74 - PCB Board
SHINKAWA FRP-270 FRP-268 - PCB Board
SHINKAWA FRP-386 - PCB Board
SHINKAWA ZUP-02C - BOARD
SHINKAWA MDP-136A - PCB Board
SHINKAWA FRP-259 - PCB Board
SHINKAWA JBP-470 - BOARD
SHINKAWA MDP-82 - BOARD
SHINKAWA FCP-07A - PCB Board
SHINKAWA DSP-09A - PCB Board
SHINKAWA IOP-178 - PCB Board
Nemic-Lambda / Shinkawa VS15C-15 CCB010A UTC-1000 - Power Supply Board
SHINKAWA IOP-176A - PCB Board
SHINKAWA VM-5C SST-2194-001-P001G - ECCENTRICITY MONITOR
SHINKAWA VM-5K SST-2194-001-P001G - VIBRATION MONITOR
THK / Shinkawa SRS9M UTC-1000 - Linear Block w/ Rail 26cm
Shinkawa JBP-316 P-26-73B-1 P-26-73A-1 UTC-1000 - Board
SHINKAWA IOP-215 - BOARD
SHINKAWA JBP-268 - PCB Board
SHINKAWA ZUP-08 - PCB Board
SHINKAWA BCP-05A - BOARD
SHINKAWA DSP-15 - PCB Board
SHINKAWA FRP-289 - PCB Board
SHINKAWA FCP-01 - BOARD
SHINKAWA MDP-84 - BOARD
SHINKAWA CMU-13A - CAMERA MOTION CONTROLLER
SHINKAWA BCP-05D - PCB Board
SHINKAWA MDP-FF MDP-87 - Stage Control Board
SHINKAWA FRP-342 - BOARD
SHINKAWA BCP-05C - BOARD
Shinkawa CMU-26A - Camera Control unit
SHINKAWA PSP-30 - Welding Machine Control Board
SHINKAWA EFU-24 - Spark Generator
Shinkawa CMU-27A - Camera Control unit
SHINKAWA CMU-44 - Camera Control Unit
THK / Shinkawa SRS9M UTC-1000 - Linear Block w/ Rail 21cm
TDK-Lambda / Shinkawa VS100B-24 VS100B24 UTC-1000 - Power Supply Board
SHINKAWA CMU-34 - Camera Control Unit
SHINKAWA FDP-06A - PCB Board
SHINKAWA BCP-06A - BOARD
SHINKAWA CMU-13A - Camera Control Unit
SHINKAWA CMU-31A - Camera Control Unit
SHINKAWA VM-5Y1-02/GEM 1594-005-P001G - ECCENTRICITY MONITOR
Shinkawa JBP-331 P-26-101B P-26-101A P26101A UTC-1000 - Board
SHINKAWA CMU-26 - Camera Control Unit
Shinkawa ACB-3000 ACB3000 - Industrial-Grade Automated Friction Bonder
Shinkawa SBB-1100 SBB1100 - Stud Bump Bonder Machine
Shinkawa ACB-1000 ACB1000 - Super Automated Wire Bonder Machine
CKD / Shinkawa FCS500-H6H6 FCS500H6H6 UTC-1000 - Precision Air Source Filter
SHINKAWA VM-5H3 1596-001-P002B VM-5Z1 3595-001-P003C - Power Supply Monitor Rack
SHINKAWA VM-5H3 2194-001-F004B - Dual Vibration Dual Thrust Monitor Rack
Shinkawa EFU-10 - Wire Bonder Spark Generator EFO Box
SHINKAWA MP-2S - Overspeed Unit Instruction
Shinkawa PK-167B-3 PK-167A-3 10P-10 - PCB Board
SHINKAWA VM-3D VM-3E VL VM-3D2 - Vibration Sensor Mit Verlangerungskabel
shinkawa FKP-452F2-3 - Sensor
shinkawa UTC-1000 ZUP-02B - PCB BOARD
SHINKAWA VM-3D VM-3E VL VM-3D2 - VIBRATION SENSOR WITH EXTENSION CABLE
Shinkawa E194236-0003 AWM 2464 UTC-1000 - Cable 6&4 Pins Female-Female
TDK-Lambda / Shinkawa VS100B-15 VS100B15 UTC-1000 - Power Supply Board
Shinkawa FK-202F2-2-1 - Electric Vortex Sensor
Marubeni Shinkawa S038493 - Rotary Encoder
Shinkawa E194236-0003 AWM 2586 UTC-1000 - Cable 10 & 8 Pins Male-Female
National / Shinkawa CAT5E NR3160 UTC-1000 - Ethernet Receptacle Connector Cable
Shinkawa LLS2902 E69157 UTC-1000 - Cable 3 Pins Male-Female
Shinkawa AWG16 600V UTC-1000 - 5 Pins Cable Female-Female
SHINKAWA WK-142K2-2 - Vibration sensors
Shinkawa DA-C8-J10 DAC8J10 UTC-1000 - Connector Cable
Shinkawa P-27-67B P2767B P-27-67A P2767A UTC-1000 - Circuit Board
Taiyo / Shinkawa E67647-WH E67647WH UTC-1000 - Computer Power Cable
Shinkawa E66085-H 20276 UTC-1000 - Connector Cable 15 Pins Male-Male
Shinkawa P-28-49B JBP-380C P-28-49A BEJ240619A UTC-1000 - Board w/
Shinkawa WKN-142K2-2 - 2-Wire vibration transmitter
SHINKAWA VM-741 VM-741B - MONITORING SYSTEM
Shinkawa FL-202F08R-U2-02-12-10 - Extension probe
Shinkawa FK-202F-1-3 FK-202F-2-3 - module
Shinkawa CMU-13A CMU13A - Camera Motion Control Unit Cut Cable
SHINKAWA VM-5J - DUAL DIFFERENTIAL EXPANSION MONITOR
Ebrain / Shinkawa 650-VME08IS-S N6071085 UTC-1000 - Backplane Panel Board
Yaskawa Electric / SHINKAWA UGQMEM-06-SW12 MD-11 - Minertia Motor w/ 30 day warranty
Shinkawa FL-202F08R-U2-02-12-10 - Extension probe
Shinkawa WT-650-16 SP-256A UTC-1000 - Power Source Power Supply AC100V 50/60Hz
Yaskawa / Shinkawa UGRMEM-01SSW11 UGRMEM01SSW11 MD-06 - Minertia Motor
SHINKAWA FK-452F1 - sensor
Shinkawa MS-313 - RPS positioning system
Shinkawa Sec M / Rn-ac109-2a - Beschleunigungsmesser
Shinkawa PFD80SX UTC-1000 - Power Source Power Supply 80V 1.6A AC100-230V
SHINKAWA VL-202A08L-1A72 - Probe extension cable
Shinkawa SDP-FA-4.1 - Instruction Manual
SHINKAWA VM-5L G0-2 GC6D1377 - Module
Shinkawa FRP-184A FRP-111 P-22-17A - Circuit Board
Shinkawa CRP-06 PK-189A-3 PK-189B-3 - PCB Board
Shinkawa WK-142K2-1 - Vibration Transmitter
SHINKAWA VM-5 SST-2194-001-P001G - MAIN BOARD DUAL VIBRATION MONITOR MAIN BOARD
Shinkawa SDP-FA-TAPE - Full Automatic Die Bonder Instruction Manual
Sanritz Automation / Shinkawa SC2125-0 C12ABP3 SC2125-0-P1 UTC-1000 - Board
Shinkawa SDP-FA-4.1 - Die Pickup Unit Instruction Manual
Shinkawa E194236-0003 AWM 2464 UTC-1000 - Cable 20 Pins Female-Female
IHI / SHINKAWA CQ71SEN004 WK-142K3-3 - 2-wire Transmitter
SHINKAWA FK-452F1 - sensor
Shinkawa D461256 - Pin Vertical Motion Cam
SHINKAWA SE02111-05 STB-FA-IL-7 - Full Automatic Inner Lead Bonder Specifications
Shinkawa PSP-25A P-26-58A-3 P2658A3 UTC-1000 - Circuit Controller Board
Shinkawa WKN-142K5-2 - Vibration Transmitter
Euresys / Shinkawa DAC-422S-A3 DAC422SA3 UTC-1000 - Alpha cPCI Board
Shinkawa IL-188-5373-23 IL188537323 - Spare Part
Shinkawa FK-202F1-3-1 - Vibration sensor
Shinkawa VL-202A08L-1018/BEN - Capteur De Proximite Avec Cable De 9 Metres
Shinkawa FK-202F-2-3 - Vibration Transmitter