Control Wave Micro 396603-01-7 Isolated Analog Output Module

Bristol Babcock Control Wave Micro 396603-01-7 Isolated Analog Output Module

The Analog Input (AI), Analog Output (AO), and Analog Input/Output (AI/O) modules provide the ControlWave® Micro with the ability to monitor and control various analog  field signals. 

The following AI, AO, and AI/O modules are available. 

6 Analog Inputs and 2 Analog Outputs module 

6 Analog Inputs module 

8 Isolated Analog Inputs module 

4 Isolated Analog Outputs module 

All I/O modules have surge protection that meets C37.901978 and IEC 801-5 specifications.

6 Analog Inputs and 2 Analog Outputs Module 

The 6 Analog Inputs and 2 Analog Outputs module provides  six analog inputs and two analog outputs. 

Analog inputs are  externally sourced, single-ended, an individually jumper  configurable for either 4 to 20 mA or 1 to 5 Vdc operation. 

Analog outputs are externally sourced (11 to 30 Vdc) and  individually jumper configurable for 4 to 20 mA or 1 to 5 Vdc. 

Surge suppression between each signal and ground is achieved with 30 Vdc transorbs. 

The 6 Analog Inputs and 2 Analog Outputs module is available with local or remote  terminations.

8 Isolated High Common Mode (HCM) Analog Inputs Module 

The 8 Isolated High Common Mode (HCM) Analog Inputs module provides eight differential analog inputs. 

Analog  inputs are individually jumper configurable as internally sourced 4 to 20 mA non-isolated operation or externally  sourced 4 to 20 mA, 1 to 5 Vdc, or 0 to 10 Vdc isolated  operation. 

The analog input circuitry is electrically isolated from the bus interface circuitry of the ControlWave Micro. 

The 8 Isolated HCM Analog Inputs module is available with local or remote terminations. 

6 Analog Inputs Module 

The 6 Analog Inputs module provides six analog input  channels. Analog inputs are externally sourced, single ended, and individually jumper configurable for either 4 to 20 mA or 1 to 5 Vdc operation. 

Surge suppression between each signal and ground is achieved with 30 Vdc transorbs. 

The 6 Analog Inputs module is available with local or remote terminations.

4 Isolated Analog Outputs Module 

The 4 Isolated Analog Outputs module provides four analog  outputs that can be individually jumper configured for 4 to 20 mA or 1 

to 5 Vdc isolated operation. Analog outputs are electrically isolated from the CPU power system.

Calibration data for each channel is stored in an onboard EEPROM for both current and voltage mode configurations. 

The 4 Isolated Analog Outputs module is available with local or remote terminations. 

Local or Remote Terminations 

All analog I/O modules are available factory configured for either local terminations that consist of 

two 10-point terminal block assemblies or remote terminations that 

consist of two 14-pin mass termination headers. 

Terminations are pluggable and accept a maximum wire size of 14 AWG (American Wire Gauge). 

Remote terminations provide a convenient alternative to the standard direct connect termination. 

Remote terminations allow a concentration of electrical connections from one or more controllers to be located in a single area, 

such as the rear of a 19-inch cabinet. 

 Applications

This isolated analog output module finds extensive applications in a wide range of industries. 

In the manufacturing sector, it can be used to control the speed of variable - speed drives, adjust the position of servo - motors, 

or regulate the flow rate of valves. 

In the energy industry, it plays a role in controlling power generation equipment, such as adjusting the output of generators or controlling the operation of pumps and compressors in oil and gas facilities. 

In building automation systems, it can be used to control heating, ventilation, and air - conditioning (HVAC) equipment, ensuring optimal environmental conditions are maintained.