ADLINK NuPRO-800 Series Full length Industrial SBC User Manual

ADLINK NuPRO-800 Series Full length Industrial SBC User Manual

Basic information 

1. Product model: NuPRO-800 (with onboard Ultra2 SCSI), NuPRO-801 (without SCSI), dual socket 37 Pentium III full-length industrial single board computer

2. Manual Version Rev1.00, released on September 6, 2000, Linghua Original Factory Official Guide

3. Copyright and after-sales service: 2000 Linghua copyright, providing global technical email and phone numbers, and a one-year original factory warranty for the entire machine;

4. Supporting materials: motherboard body, user manual, IDE/floppy drive cable, serial port parallel port board, USB board, 800 model comes with SCSI cable, integrated driver tool CD;

5. Applicable systems  Windows 95/98/2000/NT, DOS, Novell, Linux, SCO UNIX.

Core hardware specifications of the product

1. Platform Architecture

-CPU: Dual Socket370 FC-GGA slots, supporting single/dual Pentium III processors (without termination card), with a maximum clock speed of 800MHz;

-Chipset: Intel 440BX (82443BX North Bridge+82371EB PIIX4 South Bridge), FSB front-end bus default 100MHz, can be jumper switched to 66MHz;

-BIOS: Award PnP Plug and Play BIOS, supports DMI hardware information reading, OEM boot logo, hard disk virus protection, LCD panel preset, SCSI configuration menu;

-Cache: The CPU has built-in L2 cache, but there is no independent L2 cache on board.

2. Memory subsystem

-3-channel 168 pin PC100 SDRAM DIMM slots, supporting ECC verification;

-Single 64/128/256MB, maximum total capacity 768MB.

3. Display module (SMI Lynx 3DM4 SM721 AGP 2X)

-Onboard 4MB video memory (OEM optional 8MB), 128bit 2D+basic 3D acceleration;

-Simultaneously driving CRT+LCD dual screen output;

-The highest resolution is 1600 × 1200;

-Support 24/36bit LVDS LCD screen, onboard LCD power jumper switch 3.3V/5V;

-VGA interface with self recovery fuse overcurrent protection.

4. Differentiate storage interfaces between two models

1. Unique to NuPRO-800: LSI 53C895 Ultra2 Wide SCSI controller, 80MB/s, supports LVD/SE/HVD adaptation, cable length up to 12 meters, compatible with various SCSI hard drives/tape drives;

2. Universal storage: Dual channel EIDE (Ultra DMA33), up to 4 IDE devices; Soft drive interface; Supports DOM electronic disks (8MB~2GB).

5. Network and IO peripherals

-Network port: Intel 82559 PCI 100Mbps network card, 10/100 adaptive, IEEE802.3x flow control, WOL remote boot, AOL2 alarm;

- Super I/O Winbond W83977EF：

-2-channel RS232 serial port (2KV ESD);

-1 parallel SPP/EPP/ECP (4KV ESD, 30V load protection);

-Dual floppy drive support;

-USB1.1 dual pin, independent overcurrent fuse;

-5pin IrDA infrared interface;

-PS/2 split keyboard and mouse+built-in keyboard pin;

-ISA bus has high driving capability, with a maximum output of 64mA for data/address lines, and is compatible with old-fashioned ISA acquisition cards.

6. Hardware monitoring and watchdog

1. Monitoring chip W83782D: collects dual CPU fan speed, CPU temperature, chassis temperature,+5/+12/-12/+5VSB voltage, and chassis cover opening detection;

2. Programmable watchdog WDT: configured through Super I/O 2E/2F registers, with a timing range of 1 second to 255 minutes (15300 seconds), and a timeout reset of the entire machine; Provide DOS/Windows source code and testing tools.

7. Machinery, Power Supply, and Environment

-Size: Full length industrial board 338mm × 122mm;

-Power supply standard ATX, full load power consumption divided into four levels (single/dual CPU 600/800MHz), dual 800MHz whole machine+maximum memory+5V 22A;

-Environment: Working temperature range of 0-60 ℃, storage temperature range of -20~80 ℃, humidity range of 5%~95%, no condensation;

-Capacitor industry specifications: Sanyo OS CON long-life capacitor, with a lifespan of 20 years in a 65 ℃ environment and high MTBF stability.

Hardware installation, jumpers, and connectors

1. Key points for CPU and heat dissipation installation

-Dual slots can accommodate only a single CPU without the need for a terminal board;

-High frequency (>660MHz) must have a copper bottom heat sink and reinforced bonding with thermal conductive adhesive; Poor heat dissipation can cause crashes, overheating, and damage to the CPU;

-FN1/FN2 dual 3-pin CPU fan socket (12V power supply+speed detection).

2. Only 3 sets of core jumpers (with very few overall jumpers)

|Jumper | Function | Configuration Rules|

|JP5 | FSB bus frequency | 2-3 short circuit=100MHz (default); 1-2=66MHz |

|JP7 | Clear CMOS | 2-3 is normal, 1-2 is short circuited to clear BIOS parameters|

|JP11 | LCD backlight logic power supply | 2-3=3.3V (default); 1-2=5V |

3. Complete definition of all onboard connectors

Includes CN2 (58 pin LVDS LCD interface, supports 24/36 bit, backlight 12V with fuse), CN1 chassis cover opening detection, CN3 front multifunctional pin (power/reset/speaker/hard disk light/ATX standby), dual EIDE, floppy drive, parallel port, dual serial ports, VGA, RJ45 Ethernet port, dual USB, IrDA, PS/2 keyboard and mouse, built-in keyboard, NuPRO-800 dedicated 68pin SCSI socket, all interfaces provide pin definition and power protection instructions.

4. Driver CD directory instructions

The CD contains a complete set of drivers for SCSI/VGA/network card/IDE DMA/watchdog/hardware monitoring/DMI, divided into folders for various versions of Windows. The NT system provides a recommended installation sequence for drivers (network card first, SP6, then graphics card).

BIOS Basic Functions 

Onboard Award PnP BIOS Core Capability:

1. PnP plug and play resource automatic allocation;

2. DMI reads CPU, memory, and bus hardware information;

3. ACPI multi-level energy-saving sleep and key mouse wake-up;

4. Boot sector virus protection;

5. Built in 9 preset parameters for industrial LCD panels;

6. SCSI controller independent configuration menu;

The complete BIOS detailed manual is stored on the driver CD NP800 _SIOS.PDF.

Step by step installation of each hardware driver 

1. SCSI driver (NuPRO-800 only)

Compatible with LSI 53C895, covering Win98/2000/NT, DOS/Linux; When installing the NT system, it is necessary to load the SCSI driver recognition hard disk on the floppy disk and provide the complete manual upgrade steps for the device manager.

2. AGP graphics card SM721 driver

Supports Win98/2000/NT4 (NT recommends SP6 to enable AGP), manual update of INF driver for control panel display adapter, supports dual screen LCD/CRT resolution customization.

3. Intel 82559 Network Card Driver

Full system adaptation, equipped with DOS diagnostic tools, supports WOL network wake-up, distinguishes different installation processes for 98/2000/NT, and NT requires pre production of driver floppy disks.

Watchdog WDT Development 

1. The operation address of the underlying register is 0x3F0/0x3F1, and the timing unit is selectable in seconds/minutes;

2. Trigger dog feeding conditions: keyboard and mouse activity, software call reset function;

3. Supporting tools: DOS/Windows testing program test.exe, providing C language source code library, supporting secondary development and integration of industrial control software to prevent system crashes.

Hardware Doctor 

Windows visual monitoring software, relying on the W83782D chip:

-Real time monitoring of CPU/chassis temperature, various voltages, dual fan speed, and chassis cover opening status;

-Customize upper and lower threshold values, with a pop-up window and beep dual alarm for exceeding the limit;

-Backend resident tray, supporting both Chinese and English interfaces, used for long-term unmanned monitoring of devices.