ADLINK PCI/LPCI/LPCIe/cPCI-723X series 32 channel isolated digital I/O card

ADLINK PCI/LPCI/LPCIe/cPCI-723X series 32 channel isolated digital I/O card

Product Overview

1. Product positioning

The entire series is equipped with * * optoelectronic isolated digital input/output acquisition cards * *, providing 2500V/5000VRMS electrical isolation to isolate external industrial strong electrical interference, and input polarity free to adapt to various on-site switch signals; The output supports 5-35VDC drive relays and solenoid valves, covering four hardware forms of standard PCI, low version LPCI, PCIe, and CompactPCI industrial buses, divided into three types: hybrid DI/DO, pure input, and pure output.

2. Channel division of the entire series of models

|Model | Channel Configuration | Bus Specification|

|PCI-7230/LPCI-7230/LPCIe-7230/cPCI-7230 | 16 isolated DI+16 isolated DO | Standard PCI/Low version PCI/x1 PCIe/3U CPCI|

|PCI-7233 | 32 isolated digital inputs (input logic reversed) | Standard 32-bit 5V PCI|

|PCI-7234 | 32 channel isolated leakage type digital output | Standard 32-bit 5V PCI|

|PCI-7234P | 32 channel isolated source digital output | Standard 32-bit 5V PCI|

Core product features

1. * * Optoelectronic isolation classification**

-5000 VRMS high voltage isolation: PCI-7230, PCI-7233, cPCI-7230, preferred for strong interference industrial scenarios;

-2500 VRMS isolation: PCI-7234/7234P, LPCI-7230, LPCIe-7230, conventional automation scenarios.

2. * * Digital input DI capability**

-Input voltage 0~24V with no polarity; High level 5~24V, low level 0~1.5V; input resistance 1.2k Ω;

-PCI-7230/LPCI/LPCIe/cPCI-7230: DI0, DI1 two external interrupts;

-PCI-7233 exclusive * * COS state change interrupt * *: Any input level jump automatically triggers an interrupt, suitable for signal inspection.

3. * * Digital output DO capability**

-Output power supply range of 5-35VDC, Darlington transistor output;

-Leakage type output (7230/7234): maximum 500mA full duty cycle for a single channel;

-Source output (7234P): Single channel maximum 500mA pulling current, suitable for loads of different polarities;

-Multi channel simultaneous output has a total current derating limit, regulating the upper limit of total load current under different duty cycles.

4. Bus and form advantages**

-PCI: 32-bit 5V universal PCI; LPCI low version supports 3.3/5V PCI; LPCIe is x1 PCI Express;

-CPCI-7230 complies with PICMG2.0 R2.1 3U Eurocard CompactPCI industry standard;

-LPCI/LPCIe adopts thin and low PCB, suitable for compact industrial control chassis.

5. * * General functions**

-Data transmission method: Program controlled I/O (PIO);

-Wide temperature and humidity industrial adaptability, low-power design.

Detailed hardware specifications

1. Isolation input DI specification

-Number of channels: 16 channels for hybrid cards, 32 channels for pure input PCI-7233;

-Input characteristics: non-polar, 0~24V wide range;

-Separate voltage levels of 5000/2500VRMS;

-Interrupt: There are two options: dual fixed channel interrupt/full channel COS jump interrupt.

2. Isolation output DO specification

-Number of channels: 16 channels for hybrid card, 32 channels for pure output 7234/7234P;

-Output type: Darlington transistor, leakage type/source type;

-Single channel maximum 500mA drive, multi-channel synchronous output with current derating;

-The maximum power consumption of a single chip (8 channels) can be divided into two levels: 1.47W and 2.25W;

-External load power supply of 5-35VDC.

3. General environmental and electrical parameters

1. Temperature and humidity**

-Working temperature: 0 ℃~60 ℃; Storage temperature: -20 ℃~80 ℃;

-Relative humidity of 5%~95%, no condensation.

2. Board power supply (+5V/+3.3V/+12V)**

The typical working current of each model is clearly distinguished, and the power supply voltage of cPCI and LPCIe is different from that of standard PCI; The output side of PCI-7230 requires an additional external DC power supply.

3. * * Physical dimensions (excluding connectors)**

Distinguish between standard PCI, low version LPCI/LPCIe, and 3U cPCI with different length and width sizes, and adapt to different chassis specifications.

4. * * I/O interface connector**

-PCI series (7230/7233/7234/7234P): 37 pin D-Sub female socket;

-LPCI/LPCIe/cPCI-7230: 50 pin SCSI-II female socket.

Matching terminal board and cable selection

1. PCI standard card (37 pin D-Sub interface)

-DIN-37D-01: DIN rail mounted 37 pin terminal board (excluding cables);

-ACLD-9137-01: Supporting cables;

-ACL-10137-1MM: 37 pin male to male 1-meter cable.

2. LPCI/LPCIe/cPCI-7230 (50 pin SCSI-II interface)

-DIN-50S-01: DIN rail 50 pin SCSI terminal board (no cable);

-ACL-10250-1:1 meter 50 pin SCSI matching cable.

Operating system, drivers, and supporting software

1. Support system

Windows 7/Vista/XP/2000/2003 Server、Linux。

2. Bottom layer driver library

- Windows：PCIS-DASK；

- Linux：PCIS-DASK/X。

3. Upper computer development tools

1. General development: AD Loger, DAQBench, supporting [VB. NET/VC. NET/VB/VC++/BBB/Delphi]（ https://link.wtturl.cn/?target=https%3A%2F%2FVB.NET%2FVC.NET%2FVB%2FVC%2B%2B%2FBCB%2FDelphi&scene=im&aid=497858&lang=zh )；

2. Third party platform adaptation: DAQPilot (LabVIEW), DAQ-MTTLB (MATLAB).

Pin definitions for various types of connectors

The document provides a complete pin allocation table for all models, divided into two categories of interfaces:

1. * * 37 pin D-Sub (PCI-7230/7233/7234/7234P)**

Define the digital input IDI, digital output IDO, external interrupt EICOM, external ground EOGND, external load supply VDD, and isolated ground IGND pins respectively; There are differences in the pin layout among the four PCI models, with pure input cards having no DO pin, pure output cards having no DI interrupt pin, and 7234P replacing the VDD power supply pin position.

2. * * 50 pin SCSI-II (LPCI-7230/LPCIe-7230/cPCI-7230)**

The DI signal is divided into high and low differential H/L pin groups, with a unified arrangement of 16 DI+16 DO, multiple EICOM interrupts, EOGND isolation ground, and VDD power supply; The cPCI and LPCI series only have slight differences in the EICOM/EOGND ground pin.