KEBA XE 020 RFID Module

KEBA XE 020 RFID Module

The Kemro K2 XE 020 RFID module internal technical manual is a complete technical document for the KEBA operation panel matching RFID identification module, covering product usage, safety specifications, structure, installation wiring, configuration, status indication, maintenance, accessories, technical parameters, and compliance standards.

Overall architecture and working principle of the product

1. System composition

The entire RFID system consists of 7 components: RFID card, XE 020/ANT antenna module, XE 020/A processing module, operation panel, coaxial antenna cable, status LED connection line, and module to OP 3xx panel connection line.

2. Recognition performance

Recommended card RI-I02112A-03 as standard, with a typical recognition distance of 40mm when paired with an aluminum front panel.

Recognition successful: The panel LED lights up green for about 3 seconds;

It does not support simultaneous recognition of multiple cards. If multiple cards enter the sensing range, recognition will fail and the LED will turn red.

3. Module appearance interface

XE 020/ANT antenna module: includes coaxial cable interface, LED wiring port, status LED, and model label.

XE 020/A processing module: coaxial cable interface, LED interface, RJ45 interface, address DIP dip switch, model label.

Installation requirements

1. Minimum installation gap for antenna

When installing antenna modules on aluminum panels, it is necessary to strictly follow the prescribed spacing; The cables behind the antenna need to be properly shielded and protected to prevent them from causing antenna misalignment and affecting recognition distance and performance.

2. Requirements for supporting auxiliary materials

Installation requires the use of adhesive backing, isolation film, cover plate, embedded strip and other accessories to ensure stable installation structure and RF performance.

Wiring, cables, and EMC electromagnetic compatibility requirements

1. EMC cabling principles

Electromagnetic interference has the characteristics of sporadic, difficult to reproduce, and high cost of fault location. The core requirements for the wiring of this module are to shield the coaxial cable, module and panel connection lines to avoid interference from the source.

2. Power supply mode

The module is powered by the control panel through RJ45 interface, without the need for an external independent power supply.

3. Interface definition

Status LED interface: 1-pin red LED, 2-pin grounded, 3-pin green LED.

RJ45 interface (module) ↔ Operation panel: 4-pin Data -, 5-pin Data+, 7-pin+12V DC, 8-pin grounded, with the remaining pins vacant.

4. Cable specifications and length limitations

Coaxial antenna cable: maximum length 300mm.

RFID status LED cable: Use a 3-core unshielded cable.

Module and OP 3xx panel connection wire: must be shielded, with a total length of ≤ 1m.

Address configuration (DIP dip switch)

When there are multiple RFID modules in the system, hardware addresses need to be set through DIP dialing on the modules. There are a total of 4 sets of addresses supported, and the factory default address is 14H:

Adr0 Adr1 corresponding address

0 0 17H

0 1 16H

1 0 15H

1 1 14H (factory)

Meaning of Status LED Indication

The LED is located on the front of the operation panel, providing visual feedback on device operation, identification, and fault status

Green light (about 3 seconds): RFID card recognition successful, working normally.

Red light: The card cannot be recognized, the card is damaged, or the permissions are insufficient.

Constant red light: No firmware, hardware startup failure, need to contact the manufacturer.

Constant orange light: not connected to the control system, check the wiring.

Lamp off: The circuit connection is normal and in standby mode.

Start up process: briefly turn red light to orange light when powered on; If the orange light cannot be switched, it is judged as a firmware failure.

Maintenance, repair, and scrapping

Daily maintenance: The equipment is designed to be maintenance free and does not require regular maintenance.

Repair: Only KEBA official technicians can repair it. Non official repairs will void the warranty. Repair requires the use of original factory protective packaging, which is only for internal protection and cannot be directly used as logistics transportation packaging.

Waste disposal: Electronic components must be strictly scrapped in accordance with local regulations and compliance.

Accessories and spare parts list

Accessory Name Material Number

XE 020/A RFID processing module 70894

XE 020/ANT antenna module 71110

300mm coaxial antenna cable 71352

Module - OP 3xx Connection Cable 58033

RFID Status LED Connection Cable 73149

RFID card RI-I02112A-03 to be updated

Core technical parameters

Communication protocols: ISO 15693, ISO 18000-3, compatible with Euromap 65.

RF parameters: operating frequency of 13.56MHz, maximum transmission power of 250mW (typical 200mW), default sampling rate of 10 times/second (configurable).

Electrical parameters: power supply DC 12V (± 5%), data interface is serial port, physical interface RJ45.

Protection level: The processing module and antenna module are both IP20.

Dimensions: Antenna board 57mm × 53mm; Processing module (including housing) 88mm × 64mm × 21mm.

environmental conditions

Working temperature:+5 ℃~+55 ℃

Storage temperature: -30 ℃~+70 ℃

Relative humidity: 5%~95% (no condensation)

Anti vibration and anti impact: compliant with IEC 61131 standard.

Installation distance: The antenna is 40mm away from the front panel; the maximum distance between the processing module and the antenna is 30cm.

Compliance Standards and Certification

1. EU Directive

Compliant with the 99/5/EG R&TTE Radio Equipment Directive.

2. European supporting standards

Personal safety: EN 50364:2001

RF: EN 300330-2 V1.3.1

EMC Electromagnetic Compatibility: EN 301489-3 V1.4.1

Electrical safety: EN 60950-1 series

Environment/Machinery: EN 61131-2:2003

3. FCC certification in the United States

Compliant with FCC Part 15 RF equipment specifications; When the whole machine is equipped with this module, the FCC ID must be marked on the outside of the device.