OMRON ZX series (ZX-L-N) laser intelligent sensor

OMRON ZX series (ZX-L-N) laser intelligent sensor

Overall positioning of the product

ZX-L-N is an Omron laser based high-precision intelligent sensor used for precise detection of displacement, thickness, size, vibration, etc. It consists of a laser probe and a signal amplifier, supports spot/line spot, reflection/reflection detection modes, and has ultra-high resolution and stable output.

Sensor probe (core model and parameters)

1. Reflective probe (ZX-LD series)

Optical method, spot type detection, distance resolution, model

Diffuse reflection light spot 40 ± 10mm 2 μ m ZX-LD40

Diffuse reflection light spot 100 ± 40mm 16 μ m ZX-LD100

Diffuse reflection light spot 300 ± 200mm 300 μ m ZX-LD300

Diffuse reflection beam spot 40 ± 10mm 2 μ m ZX-LD40L

Diffuse reflection beam spot 100 ± 40mm 16 μ m ZX-LD100L

Diffuse reflection beam spot 300 ± 200mm 300 μ m ZX-LD300L

Regression reflection light spot 30 ± 2mm 0.25 μ m ZX-LD30V

Regression reflection beam spot 30 ± 2mm 0.25 μ m ZX-LD30VL

2. Contrast probe (ZX-LT series)

Detection width, detection distance, resolution model

φ1mm 0~2000mm 4μm ZX-LT001

5mm 0~500mm 4μm ZX-LT005

10mm 0~500mm 4μm ZX-LT010

30mm 0~500mm 12μm ZX-LT030 0.5M

3. General parameters of the probe

Light source: 650nm visible light semiconductor laser

Reflective type: Output * * ≤ 1mW * *, EN 2/FDA II

Opposite type: output * * ≤ 0.35mW * *, EN 1/FDA I

Working temperature: 0~50 ℃, storage: -15~60 ℃ (reflection)/-25~70 ℃ (reflection)

Protection level: IP40/IP50

Linearity: Maximum * * ± 0.2% FS**

Temperature characteristics: ± 0.03% FS/℃ (high-precision type)

Amplifier Unit (ZX-LDA11-N/ZX-LDA41-N)

1. Electrical specifications

Power supply: 12-24VDC ± 10%, ripple ≤ 10%

Power consumption: ≤ 140mA (24VDC)

Working environment: 0~50 ℃, 35%~85% RH

Insulation: 500VDC 20M Ω, withstand voltage 1000VAC for 1 minute

2. Output and Function

Linear output: 4~20mA (load ≤ 300 Ω)/± 4V (impedance 100 Ω)

Judging output: 3 channels (HIGH/PASS/LOW), NPN/PNP optional, 30VDC 50mA

Measurement cycle: 150 μ s

Average frequency: 1~4096 adjustable

Core functions: Peak holding, zeroing, teaching, delay, mutual interference suppression, laser anomaly detection

Expansion accessories

Computing unit: ZX-CAL2 (supports A+B/A-B operations, anti-interference)

Communication unit: ZX-SF11 (RS-232C, CompoWay/F protocol)

Software: ZX-SW11EV3/ZX-SFW11EV3 (settings+logs)

Extension cable: ZX-XC1A/4A/8A/9A (1~9m)

Side view accessories: ZX-XF12/ZX-XF22

Laser safety and usage regulations

Reflective type: EN Class 2, FDA Class II

Targeted type: EN Class 1, FDA Class I

Do not look directly at the laser, the optical path must be closed

Use alcohol soft cloth to clean the lens, do not use thinner

Preheat with power for about 10 minutes to achieve stable accuracy

Key issues

Question 1: What is the highest resolution of the ZX-L-N series sensor and which model does it correspond to? What are the differences in resolution among different detection methods?

Answer: The highest resolution is 0.25 μ m, corresponding to the ZX-LD30V/ZX-LD30VL retro reflective probe; Due to the detection distance and spot design of diffuse reflection and reflection, the resolution is between 2~12 μ m, and the high-precision mode of short distance regression reflection can reach 0.25 μ m.

Question 2: What are the output types and judgment functions of the amplifier unit, and how do they meet the requirements for different control system connections?

Answer: The amplifier supports dual-mode output of current (4~20mA) and voltage (± 4V/1~5V), with bottom switch switching; Equipped with HIGH-PASS/LOW 3-channel judgment output, with two optional output types of NPN/PNP, it can be directly connected to different systems such as PLC and industrial computer.

Question 3: How to classify the safety levels of ZX-L-N series lasers and what core safety requirements must be followed when using them?

Answer: The reflective type is EN 1/FDA I (safety level), and the reflective type is EN 2/FDA II (low-power visible light); Core requirements: It is forbidden to directly look at the laser, the optical path should be closed to avoid reflection, the protective shell should not be disassembled, and the probe connector should not be plugged or unplugged when powered on.