GE IC200ALG264 Analog Input Module

GE IC200ALG264 Analog Input Module

Module features include:

ƒ Fifteen single-ended input channels, one group

ƒ Jumper selection of 4-20mA or 0-20mA operating range

ƒ Fifteen bit converter resolution

ƒ Software-configurable selection of default/hold last state operation

Host Interface________________________________________

The module provides 15 words of analog input data.

Diagnostics _________________________________________

The module reports a Loss of Internal Power fault for field-side circuits.

The module reports an Open Wire fault for each channel, when in 4-

20mA mode.

LED Indicators _______________________________________

The green OK LED is on when backplane power is present, internally

generated field power is functioning properly, the module has been

configured, and the module has been recognized on the backplane.

Configuration Parameters ______________________________

A jumper on the carrier terminals can be used to configure 4-20mA or

0-20mA input ranges. With no jumper installed, the module accepts 4-

20mA input signals. With a jumper installed, the module accepts 0-

20mA input signals.

The analog inputs are software-configurable to either default or hold last

state upon a loss of module

Module Characteristics

Channels 15 single ended, one group

Module ID FFFFB50F (when cfg for 4-20mA range)

FFFFB40F (when cfg for 0-20mA range)

Isolation:

User input to logic (optical)

and to frame ground

Group to group

Channel to channel

250VAC continuous; 1500VAC for 1 minute

Not applicable

None

LED indicators OK LED indicates successful power-up and

configuration

Thermal derating None

Backplane current consumption 5V output: 100mA maximum

External power supply None

Configuration parameters Range select (terminal jumpers)

Diagnostics Loss of Internal Power,

Open wire detection of 4-20mA signals only

Input Characteristics

Input current 4 to 20mA (default: no terminal jumper installed)

0 to 20mA (with terminal jumper installed)

Input Impedance 100 Ohms

Accuracy at:

25 degrees C *

0 to 60 degrees C

+/-0.3% typical of full scale,

+/-0.5% maximum of full scale

+/-1% maximum of full scale

Resolution 15 bits

0.5µA = 1 counts (for 4-20mA range)

0.625µA = 1 counts (for 0-20mA range)

Filter response

(3dB Corner Freq)

24 Hz +/-20%

Update rate 7.5ms

* In the presence of severe RF interference, (IEC 1000-4-3. 10V/m), accuracy may be

degraded to +/-2%.

Preinstallation Check ________________________________

Carefully inspect all shipping containers for damage. If any equipment is

damaged, notify the delivery service immediately. Save the damaged

shipping container for inspection by the delivery service. After unpacking the

equipment, record all serial numbers. Save the shipping containers and

packing material in case it is necessary to transport or ship any part of the

system.

Terminal assignments for the module are shown below.

Number Connection Number Connection

A1 I1 B1 No connection

A2 I2 B2 No connection

A3 I3 B3 No connection

A4 I4 B4 No connection

A5 I5 B5 No connection

A6 I6 B6 No connection

A7 I7 B7 No connection

A8 I8 B8 No connection

A9 I9 B9 No connection

A10 I10 B10 No connection

A11 I11 B11 No connection

A12 I12 B12 No connection

A13 I13 B13 No connection

A14 I14 B14 No connection

A15 I15 B15 No connection

A16 Range JMPR B16 No connection

A17 RTN B17 No connection

A18 NC B18 No connection

Wiring Connections for Carriers with Two Rows of Terminals

The diagram below shows wiring connections for this module when

installed on a carrier with two rows of terminals.

1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 10

I1 Range

JMPR I2 I3 I4 I5 I6 I7 I8 I9 I10 I11 I12 I13 I14 I15

A

Wiring Connections for Carriers with Three Rows of Terminals

The next diagram shows wiring connections for this module when

installed on a carrier with three rows of terminals.